Header banner
Revain logoHome Page
🌊 inkbird detachable aquarium probe: ultimate temperature control solution for itc-308 itc-306t and itc-308s freshwater saltwater aquarium logo

🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium Review

6

·

Excellent

Revainrating 5 out of 5  
Rating 
5.0
🛠️ Scanners & Testers, 📏 Measuring & Layout Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium
img 2 attached to 🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium
img 3 attached to 🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium
img 4 attached to 🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium

Description of 🌊 Inkbird Detachable Aquarium Probe: Ultimate Temperature Control Solution for ITC-308 ITC-306T and ITC-308S Freshwater Saltwater Aquarium

☑☑Plug and play detachable aquarium probe. ☑☑Sensor Length: 2m / 6.56ft. ☑☑It's ONLY compatible with INKBIRD's following controllers: ITC-308S. ☑☑The probe is made of plastic material. ☑☑Specially designed for aquarium products.

Reviews

Global ratings 6
  • 5
    6
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

The picture is inaccurate

This is not compatible with 308, obviously it is compatible with 308S. And does not come with the braid shown in the picture.

Pros
  • Amazing
Cons
  • New competitors have emerged

Revainrating 5 out of 5

Excellent product in test, measurement and verification

I use this product to warm turtles. I gave it four stars for accuracy because it's always off by about two degrees. Otherwise it's super reliable.

Pros
  • Excellent overall performance
Cons
  • Not all fit

Revainrating 5 out of 5

Came with pigtails, soldered on the board and voila!

I was skeptical of the reviews that said it did not contain pig tail. Mine came with the end of the braid. I soldered it to the circuit board, remembering which hole was for the white wire. New probe connected and everything worked. The old sensor showed 107, over 20 degrees. I read online that the sensors can drift after about 3 years. This new one reads for sure :)

Pros
  • Industrial & Scientific
Cons
  • I am writing back

Revainrating 5 out of 5

Mandatory when used with an aquarium

It is not clear from the product description if it can be used with the ITC-308. When I bought my device, I knew the sensor wasn't designed for constant immersion, but I took a risk. After a few years the sensor failed and its readings got much higher than my high alarm threshold. I ordered this replacement sensor and installed it. The sensor works great, it is now rated for underwater use and has a plug. So if I need to replace it again, I can easily replace it.

Pros
  • Test, measure and test
Cons
  • Not sure

Revainrating 5 out of 5

Worked as a replacement for ITC-308

I replaced the sensors on two of my Inkbird ITC-308 and they worked great. The sensors I received were the same as in the picture, with a DC jack pigtail and a suction cup on the cable. I decided to solder the pigtail to the board instead of cutting the probe wire and splicing a new one. Temperature measurements are very accurate. I compared it to a calibrated scientific digital thermometer and it showed an error of only 0.1F. The probe is short and made of hard black plastic, which differs…

Pros
  • Temperature and Humidity
Cons
  • Out of fashion