📱 DigiMo 2-in-1 Phone Car Holder & Tablet Truck Mount with Flexy Gooseneck Swivel Cradle - Compatible with iPhone 11 Pro XS MAX X XR 8 Plus, iPad Mini, Samsung Galaxy Note & S-Series (4.5-8 inch) Review

It worked really well! I use it to view live data on my tablet via an OBD-II sensor. I don't plan on removing it from the car so I used the bracket that came with it and attached the arm to the center console. With the orthosis I have no problems with wobbling or any kind of instability. I have a 2016 Ford Taurus and I attached it to the right front driver's side bolt. You need to remove the plastic cover and loosen the seat screw. Then it just slides in and you tighten the seat bolt. Please…

works very well. The hand is very hard. need longer. I have a 2015 Jeep Grand Cherokee and the bracket is about 1" above the side of the console. The lever is incredibly stiff. I like that it's strong, but it seems overly complicated. I see no reason to make the lever that strong, especially when the mount itself is just a cheap little piece of plastic, either go all the way and make the mount a bit too strong, or relax your hand a bit on the mount itself is a typical cheap plastic adjustable…

Pros: Very strong and stays in place without much vibration. Holds the tablet well and rotates well. Since anything mounted on an extension cord is subject to vibration, this one works pretty well. Good materials and well finished. for my Subaru Outback when attached to the seat bolt and holding a 7-8 inch tablet. The edge of the tablet would rest against the shift knob unless seated in the passenger footwell or oriented vertically. I could lift it up if I wanted to install it with the included

Just received this and fitted it to my 95 Nissan Sentra GXE. It's a lot more stable than I thought. My tablet, the nVidia Shield K1 gaming tablet, is a bit heavy but wobbles a bit when driving on the road. The gooseneck is very stiff and very difficult to bend, which is good, it stays where you bend it. I used all 4 long support legs as using only 2 short and 2 long legs was very tight on my tablet. Also, the long support legs flex with a lot of pressure on them. It was very easy to install…

My husband installed it a few days ago and I used it straight away. It holds my LG tablet firmly and for everyday use I position the tablet horizontally. (I use a tablet to input the Sirius XM radio in the car so I can listen to it on the way to work.) That's good for that, but I was hoping that with the tablet standing upright it would work with it i could use a bigger gps than my phone. My conclusion after this weekend trip! It is excellent! I have a Nissan Versa Note (small narrow car) and…

When I ordered this mount I was expecting a bathroom vanity mirror style neck but was surprised by the strong steel neck! Despite this, it is easy to install and bend into the desired position. It does have a slight vibration issue when not used with the included boost clip, but that's due to the approximately 2-foot length of the neck and isn't a design flaw. The adjustable mounting head is pretty sturdy, with two different mounting brackets for larger and smaller devices. The instructions are

2nd review after second purchase: The second phone holder was purchased for a 2017 Ford Expedition and is quite short for a large SUV. So unless you have the talent to make an extension (see photo) of about 6 inches, don't buy it. If you have about an hour and you have the tools, a piece of a broken hockey stick with one side removed will do, move on. However, the overall lower score isn't because they're too short. I knew this could happen before I ordered. It worked great in my other car for…

Review 2/27/17: I've been looking for a tablet car mount for my Samsung Galaxy E Lite for weeks; I finally went with it as I couldn't find a mount that could hold the little E Lite. Anyway, I received the mount on 02/25/2017 and immediately mounted the device to the seat mount as instructed. This part was easy and took less than a minute. The package included three sets of brackets to attach to the bracket head. It took me a few minutes to experiment with each set of mounts to see which one…