Header banner
Revain logoHome Page
πŸ”§ upgraded carburetor for tecumseh 632615 632208 632589 h30 h35 logo

πŸ”§ Upgraded Carburetor for Tecumseh 632615 632208 632589 H30 H35 Review

4

Β·

Very good

Revainrating 4.5 out of 5Β Β 
RatingΒ 
4.3
πŸ›Ί Motorcycle Parts, 🏍️ Motorcycle & Powersports

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ”§ Upgraded Carburetor for Tecumseh 632615 632208 632589 H30 H35
img 2 attached to πŸ”§ Upgraded Carburetor for Tecumseh 632615 632208 632589 H30 H35
img 3 attached to πŸ”§ Upgraded Carburetor for Tecumseh 632615 632208 632589 H30 H35
img 4 attached to πŸ”§ Upgraded Carburetor for Tecumseh 632615 632208 632589 H30 H35

Reviews

Global ratings 4
  • 5
    1
  • 4
    3
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

I should have read this review before buying!

So I took the bowl off to see if it was the same as the original carburetor and it was. I put everything back together, and when I did, I tightened the main jet screw and didn't tighten it, but neatly. It immediately broke in half. I had to use an extractor to get it out, but if I were to buy it again I would buy an additional recovery kit with it because chances are something will break either out of the box or along the way. You can also see that it has been finished with rough edges on the…

Pros
  • Motorcycle & Powersports
Cons
  • Something else

Revainrating 4 out of 5

The old Sears tiller now purrs like a kitten

I have to deduct at least one star because the throttle linkage is not the same as the old carburetor. I tried making my own links and no matter what I did the geometry just didn't work right. Throttle linkage and lever will bind and therefore not open the throttle. My solution was to remove the throttle body and stem from the old carb and install them on the new one. The problem is that the holes for connecting the small wire links are in the 3 o'clock position, not the 12 o'clock position…

Pros
  • Parts
Cons
  • Some Cons

Revainrating 5 out of 5

Perfect replacement for carburetor with primer bulb

It was purchased to replace the carburetor on an Eagle One Edger. The diagram shows carburetor part number 632589 and the original carburetor used a primer lamp for the starter circuit. Unfortunately, this carburetor is apparently no longer available. This carb claims to be compatible, but instead of a primer bulb, it has a choke. Not finding anything else, I decided to give it a try. After installation, the edge cutter started and worked perfectly. I had to adjust the idle mixture screw - the…

Pros
  • Automotive
Cons
  • old

Revainrating 4 out of 5

Not Exact Match-Works

The objective was to find an identical carburetor to replace the Tecumseh 3hp Model H35 4-Stroke engine. The search revealed that it is a replacement. However, when opening the box, the assembly patterns of the manifold and filter were the same, and the gas line connection was correct. The replacement also featured a throttle and choke lever that the previous carburetor did not have. But the original carburettor has some kind of primer bulb and an additional rubber hose between the head and the

Pros
  • Carburetor
Cons
  • Unfashionable