Single Hand Mixing Valve Ceramic Cartridge Review

Bought to replace an old cartridge that is 20 years old. I cleaned the old one, it began to work like new, but when I wanted to lubricate it, it just fell apart. He worked freer than new. But the best is the enemy of the good. I made a purchase in the Pro_Design store through . Accordingly, the photos of the cartridge from this store.

The kitchen faucet, which had served for more than 10 years, began to creak and turn hard. Dismantling and lubricating the cartridge mechanism, of course, did not help, so a new cartridge was ordered and successfully installed. It differs from the old one in color. in the photo the new one is blue and the old one is beige. Most likely, I will also change the cartridge in the bathroom. Thank you very much to the seller for the prompt and high-quality delivery.

Replaced cartridge 2022 release. This one stood up like a native. No dancing with a tambourine! Removed the old one, cleaned the rubber landings, installed the new one.

I put one screw from an old mixer, and I had to change the upper plastic nozzle to the old one - the handle did not sit in place. The replacement itself is simple. Works smoothly))

One drawback, in the new set for changing the cartridge there is a plastic ring that did not fit . The complete set with a tap comes with a soft, rubber ring, which I had to put with the new set .

Searched everywhere. They shrugged their hands in stores, on the official website the price was 3700 + 900 delivery. Here bought a little more expensive 1500

The mixer has worked for 12 years, but nothing is eternal. The lever began to move jerkily and very tight. Bought the cartridge and installed it in 20 minutes. Now it works like new. The good news is that after more than 10 years you can buy spare parts from Grohe

While I was waiting for the package, I took off the old cartridge (not without incident - the faucet handle in the bathroom was tightly welded), beige (18 years old, cold water began to ooze from under the cartridge) - there was a crack in the case from the cold water side. I washed everything in Sanoks, along with a silicone gasket (it stood separately and is smaller in size), a cartridge and an internal cavity of the tap (chiara) - I put it back - while everything works - it does not leak…

I'm glad the cartridge has a spare bracket and screws, but the teeth on the side of the cartridge don't line up with the groove on the hub. I have searched the internet for several photos and all the photos only show teeth. I even called Grohe and they couldn't help without a model number as the cartridge is used in many of their models. We are the second owners and the soul is around 20-25 years old. I ended up using a dremel to groove the original bushing to match the teeth. It fits and works

I was sad to discover my kitchen sink was leaking the other day. I went to a regular plumbing store and heard that the only place they "could" sell the Grohe brand was about 30 miles away. I did a bit of digging (disassembled the faucet with no parts) and found the model number of my sink. I ordered this device and the next day it was happily at my door. I've rebuilt the faucet before (in case anyone needs water) and the old one hasn't lost a drop since getting the new valve assembly. It seems…

This rating applies to both Grohe products. Designed and produced by The Superior Race. So here's the story. In the last 6 months the 'black coating' has 'peeled' off the handle exposing the Brite stainless steel handle. So I decided to replace the OurGrohe handle until I realized they cost about $340. Because I wasn't willing to spend that much, and upon further investigation, I found a new "filter" at Revain (the product in this review) and a new pen for a "combined price" of $130. It's $130.

This mixer valve did not come with the correct parts to install in my old Grohe LudyLux Cafe kitchen faucet. Came with a very long and a short main screw. I had to use the same long screws from my old valve. I also had to use old gaskets, which is undesirable. Although the valve appears to be symmetrical, it will only be properly tightened when the outer cap is properly seated on one side. It took me quite a long time to figure that out. It took some time to remove the cap around the valve as…

I have a Grohe Ladylux Pro 12 years old (2009) and it started dripping from the handle. Miraculously I was able to find the installation instructions and with the help of mighty Google found this part here at Revain. The hardest part was disassembling the faucet. I have included photos of the instructions and schematics from my old manual (not the manual that came with the package). There were difficulties (part numbering from the attached instructions): 1) The diagram says a 3mm hex, but…

I noticed my 6 year old Grohe Bridgeford faucet was starting to leak around the handle. I did a google search and found it was cartridge related and needed to be replaced. With further google searching I found that the cartridge part number for this faucet is 46048000. This particular faucet model has been discontinued, but replacement parts are still available. I found a plumbing store that had this part, but on a whim I decided to give Revain a try. lo and behold, here in the sanitary trade…

It's great that Grohe has fitted their expensive faucets with a relatively inexpensive one-piece replacement part to fix leaks. My 10+ year old Ladylux Plus started leaking from the pen and googling the symptoms led me to this Revain cartridge. The replacement cartridge cost less than 10% of the original faucet and took about 90 minutes to replace. Most of the time you're trying to figure out how to remove the handle to get at the cartridge. If I had to do it again, it would probably take 10…