Header banner
Revain logoHome Page
πŸ”Œ 12-volt single spst on-off switch with bezel for rv, trailer, camper - american technology components (almond) logo

πŸ”Œ 12-Volt Single SPST On-Off Switch with Bezel for RV, Trailer, Camper - American Technology Components (Almond) Review



Very good

Revainrating 4 out of 5Β Β 
πŸ“± RV Electronics, 🚐 RV Parts & Accessories

View on Amazon


img 1 attached to πŸ”Œ 12-Volt Single SPST On-Off Switch with Bezel for RV, Trailer, Camper - American Technology Components (Almond)


BrandAmerican Technology Components
Item Dimensions LxWxH2.8 x 1.8 x 1.25 inches
Specification MetCSA

Description of πŸ”Œ 12-Volt Single SPST On-Off Switch with Bezel for RV, Trailer, Camper - American Technology Components (Almond)

SPST, 16 Amp @ 125-250 VAC, 3/4 H.P. @ 125-250 VAC, 10 Amp @ 14 V (T), 3 Amp @ 125V(L) UL/CSA/VDE approved. Commonly used for lights, pumps, fans, vents and many other uses in RVs, Buses, Horse Trailer Conversions, Haulers, Travel Trailers, Boats and more. Switch size with bezel 2 7/8'' ( 2.875'') L x 1 7/8'' (1.875'') W. Single Cutout Dim: 1 1/8”W x 1 1/2”L. Includes 1 switch plate and cover, Made in the U.S.A.


Global ratings 9
  • 5
  • 4
  • 3
  • 2
  • 1

Type of review

Revainrating 5 out of 5

Too much work! for RV parts and accessories

This switch is not surface mount. Notice a square bump on the back of the switch. You need to cut a square notch before the switch is flush.

  • Slim design
  • Operating speed

Revainrating 5 out of 5

much cheaper than dealer

broken switch in my RV. When looking at replacement parts, the dealer cost was three times higher for the same item. Bought a few more just in case, but so far everything looks and works well.

  • High marks for support and durability from testers
  • damaged

Revainrating 4 out of 5

Easy to install on RV parts and accessories

I bought a switch so my wife can turn off the light above the bed in our RV. The switch works great and is easy to install. Keep in mind that even though it's on the surface, it requires a hole for the wires and the back of the switch needs to be below the surface.

  • GOLS certified
  • Not sure

Revainrating 5 out of 5

Soldering wires is too risky

I removed the star because when soldering the wire to the terminal, the plastic around the terminal began to melt and loosen. The plastic melted in front of my solder! It shouldn't melt so easily. After that it didn't work. I'll disassemble it and see if I can fix it.

  • Strong finish
  • I don't remember

Revainrating 5 out of 5

Works great best in RV parts and accessories

Worked well. Follow the minimum hole size guidelines. Depending on the material you are cutting, you will need screws of the appropriate length/size. I used screw #6 and it worked fine. For my application I soldered the wires to the connectors on the back panel. I prefer as this method provides a good mechanical and electrical connection. Retractable terminals should also work.

  • Nice packaging
  • Minor

Revainrating 1 out of 5

Constantly blows up my 12v circuits

Don't like that you have to use spade connectors which are not included and add them to your wiring to be able to connect to the back of the switch. Then I noticed that every time I used the switch, the circuit would break. Then the one on the other side of the RV did the same. This is not my wiring as I made a direct connection and everything works fine. Not worth the money and not recommended.

  • Wow
  • No power

Revainrating 5 out of 5

Same as the original for RV parts and accessories

Works as expected. Corresponds to the original in my 2007 Winnebago Access 29T. I just wish there was a way for me to gloss over the switch's description like the original. Using a label printer doesn't look that great. I also drilled a hole in one corner of the front panel and added a red LED that lights up when the circuit is on. LED from this list.

  • Lots of good vibes
  • Few little things

Revainrating 3 out of 5

Nice little 12v RV switch (but doesn't always respond)

Love the look and easy installation of this switch. The only thing I don't like is that when I turn on the switch, the element doesn't always turn on. But simply turning it off and on again seems to always (or almost always) turn the Element on. I installed it for a small 12v fan to cool the cabinet with a convection microwave which seems to get the cabinet a little hotter than I would like.

  • Weight
  • Something else

Revainrating 5 out of 5

good quality switch

This is an identical replacement for Grand Design OEM switches. I had the dealer install a fan in the bedroom of my new RV. They were powered by a light switch controlled by the switch, so the fan only turned on when the switch was turned on along with the lights (yes, that's right). So I bought two of these and lined them up for each light so I could turn the lights on and off individually. They came in quickly after creating and setting up the holes. These are not hot switches. I don't need…

  • cool product
  • vanishing