Header banner
Revain logoHome Page
🔪 carbide coated spetool flutes in inches logo

🔪 Carbide Coated SpeTool Flutes in Inches Review

7

·

Average

Revainrating 4 out of 5  
Rating 
3.9
🔧 Milling Accessories, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔪 Carbide Coated SpeTool Flutes in Inches
img 2 attached to 🔪 Carbide Coated SpeTool Flutes in Inches
img 3 attached to 🔪 Carbide Coated SpeTool Flutes in Inches
img 4 attached to 🔪 Carbide Coated SpeTool Flutes in Inches

Description of 🔪 Carbide Coated SpeTool Flutes in Inches

Solid Carbide Spiral Router Bit with 1/4 inch Shank and 1/4 inch Cutting Diameter, 1-1/8 inch Cutting Length, 3 inch for Total Length. Flat Top with 2-Flute, Material: HRC55 Carbide with TiAlN Coated. For CNC,Engraving Machine.Carbon Steel, Mould Steel, Inconel, Stainless Steel, Titanium Alloy etc. The Route Bit Suit for CNC Router and Makita, Bosch, and Any Brand Plunge Router with 1/4" Collet. End Mill Bits are Suitable for Side Milling, End Milling, Finish Machining, etc.

Reviews

Global ratings 7
  • 5
    3
  • 4
    2
  • 3
    0
  • 2
    2
  • 1
    0

Type of review

Revainrating 5 out of 5

Poor quality, good for square nose

Broken on first use. I do not recommend. , I have on site Bought a more expensive replacement but I've made dozens of holes with it.

Pros
  • Suitable bit for CNC router, Makita plunge router, Bosch and any other brand with 1/4" collet
Cons
  • Definitely bad product

Revainrating 5 out of 5

Good quality tool, best end mill

I use this tool on a CNC router to cut acrylic and it holds up very well. There was a mix up with my original order when they sent the wrong tool. After contacting the company, the correct one was sent. No problem. I will definitely order more.

Pros
  • 2 flute flat top Material: TiAlN coated HRC55 carbide
Cons
  • Hard to tell

Revainrating 2 out of 5

Easily snaps into place for cutting tools

Bought these for milling aluminum and they broke almost as soon as they touched. I hoped 10 seconds would go smoothly and boom. I think if I didn't need the length it would be fine like some of the other reviews said but I got it for the length.

Pros
  • End mills are good for side milling, face milling, finishing etc.
Cons
  • Slightly torn

Revainrating 4 out of 5

Good for short jobs, doesn't stay sharp for long.

Bought these for a small CNC job needed a longer range. I had to complete the task 6 times, each task took about 1 hour to cut a walnut. These bits took 3 jobs before they got boring. That's not bad for a $16 bit. Since I don't need that much time, it was definitely worth the money.

Pros
  • 1/4" shank carbide spiral cutter with 1/4" cutting diameter, 1-1/8" cut, 3" overall length
Cons
  • Not bad but...

Revainrating 5 out of 5

Good quality tool, best in cutting tools

I use this tool in a CNC router to cut acrylic and it holds up very well. There was a mix up with my original order when they sent the wrong tool. After contacting the company, the correct one was sent. No problem. I will definitely order more.

Pros
  • Great for a small home
Cons
  • Questionable purchase for the elderly

Revainrating 2 out of 5

Easy snap on for router accessory

Bought for aluminum router and it clicked almost immediately when touched. I hoped 10 seconds would go smoothly and boom. I think if I didn't need the length it would be fine like some of the other reviews said but I got it for the length.

Pros
  • Cool product
Cons
  • Something different

Revainrating 4 out of 5

Good for short jobs, doesn't stay sharp for long.

I bought these for a small CNC cycle that needed more reach. I had to complete the task 6 times, each task took about 1 hour to cut a walnut. These bits took 3 jobs before they got boring. That's not bad for a $16 bit. Since I don't need that much time, it was definitely worth the money.

Pros
  • Consistent test results
Cons
  • Could have chosen a newer model