Header banner
Revain logoHome Page
🐠 enhanced uxcell silver metal 2-way co2 tank splitter regulator valve for aquarium plants logo

🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants Review

4

Β·

Very good

Revainrating 4 out of 5Β Β 
RatingΒ 
4.0
🐠 Aquarium Pumps & Filters, 🐠 Fish & Aquatic Pets

View on AmazonView on Π―M

Media

(4)
img 1 attached to 🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants
img 2 attached to 🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants
img 3 attached to 🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants
img 4 attached to 🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants

Description of 🐠 Enhanced UXCELL Silver Metal 2-Way CO2 Tank Splitter Regulator Valve for Aquarium Plants

Package Include: 1 x CO2 Splitter; Size: 9.5x7x3cm / 3.74"x2.76"x1.18"(L*W*H). For 4mm/6mm air hose tubing. For CO2 tank use. Good for aquarium plants. Easy setup, no modification required to your CO2 regulator. Each outlet is equipped with an individual needle valve allowing precise regulation of CO2 flow. With this splitter, you can connect up to three CO2 diffusers/supplies from a single CO2 cylinder.

Reviews

Global ratings 4
  • 5
    1
  • 4
    2
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Works Great - Aquarium Pumps and Filters

I have a 125 gallon and didn't think of a diffuser would suffice.I bought this splitter and another bubble counter and diffuser Just don't over tighten I broke the o-ring but there was another one with a bubble counter that I bought so it worked.I have two now Bubble counter with two diffusers, 6' green on both sides of the tank.

Pros
  • Package Contents: 1 x CO2 Splitter; Size: 9.5 x 7 x 3 cm / 3.74" x 2.76" x 1.18" (L*W*H)
Cons
  • Update Availability

Revainrating 4 out of 5

ALWAYS use O-rings!

Nice little splitter. Apparently you should install it, run your CO2 for 1-2 hours, then check and reset. It stays true after a reset (at least for me) and I really think it has more to do with the CO2 flow than the splitter when first turned on. Also make sure to USE O-RINGS on each mount! It came with them in the place where the bubble counters are attached, but I didn't have the bubble counter in the regulator port. If you don't, chances are it will leak. good thing though :)

Pros
  • Each outlet is equipped with an individual needle valve for fine adjustment of the CO2 flow.
Cons
  • Big and chunky

Revainrating 3 out of 5

Disconnects, holds but does not actuate needle valve

it did not lick and the male fed one for two. so I would give C. but the valve on this one is very useless. a) If you loosen it further it will pop out, adjustment is almost nonexistent at low flow. This can be useful for serving one side of the feed, then the other. but if you're thinking, "Oh, maybe there's an adjustment to that." Nope. The built-in, semi-expensive needle valve is on my "next thing I'll spend money on" and accepts 4mm diameter x 6mm OD polyurethane (pneumatic) tubing with no…

Pros
  • Up to three CO2 diffusers/supplies from one CO2 cylinder can be connected to this splitter.
Cons
  • long wait

Revainrating 4 out of 5

I have a problem with the CO2 distribution

I use this for my 90 gallon and my 29 gallon planted tanks but I don't know if I set it up correctly. If anyone can help me I will change the rating. Only one side of the collector works correctly. Edit: Turns out my CO2 tank was low and also my regulator was just plain bad. When I fill up my tank and swap out my regulator, the CO2 pumps out a little better on both sides. But one side still can't get the same number of bubbles per second as the other. Which is good for my current situation as I

Pros
  • Easy setup, no CO2 regulator modification required.
Cons
  • Some little things