Header banner
Revain logoHome Page
westar em 2564 engine mount logo

Westar EM 2564 Engine Mount Review

7

·

Average

Revainrating 3 out of 5  
Rating 
3.0
🚗 Transmission & Drive Train, 🛠️ Replacement Parts

View on AmazonView on ЯM

Media

(1)
img 1 attached to Westar EM 2564 Engine Mount

Description of Westar EM 2564 Engine Mount

Provides a locking mechanism to lock the strut and body together. Our factories use only top quality components, and manufacture to strict ISO, QS, and TS standards. Designed for your specific vehicle, whether it uses a rubber, hydraulic, vacuum assisted, or electronic. Provides a noise dampening system to prevent noise and vibrations from the road from making their way into the vehicle. Fit type: Vehicle Specific.

Reviews

Global ratings 7
  • 5
    1
  • 4
    2
  • 3
    2
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

Doesn't fit - Transmission mounts

Doesn't fit. The hole was enough for the bolt not to fit, had to be cut through to fit, ended up just going back and getting one from the auto zone.

Pros
  • Sturdy construction
Cons
  • Some difficulties

Revainrating 4 out of 5

Low price, worked well

Worked very well. I had to drill some holes to align/fit them properly, but other than that it's great. The price is really great, I can't complain.

Pros
  • Few competitors
Cons
  • -

Revainrating 4 out of 5

Mounts closest to OEM

As other aftermarket mounts like Anchor drop in quality (and DEA and Pioneer make pure junk), it's good to see Westar making mounts closer to OEM fit and -Quality manufactures. If you don't want to pay dealer prices (or the part is obsolete) this is the best alternative!

Pros
  • Free for educational purposes
Cons
  • Has flaws

Revainrating 3 out of 5

They generally fit, but from the driver's side.

They generally fit, however the driver's side had to be modified a bit to fit properly. In that sense, the design could be improved. I would buy again if needed and hope to have no trouble fitting the motor this weekend.

Pros
  • Delivery was very quick
Cons
  • Some issues

Revainrating 1 out of 5

This is a bad replacement for the original brackets

Poor replacement for the original brackets. The bolt is offset about 1/2 inch from the factory mounts, making installation nearly impossible. I will have to buy another set of brackets, hopefully they will fit better than this one.

Pros
  • Everything is fine!
Cons
  • Expensive

Revainrating 5 out of 5

Good quality for the price

For the price I think this mount is well made. It took some effort to remove the bolts from my original mount, but then the new mount slid right in (lifting the motor from that side). The clutch in my truck sticks, sticks and "jumps" when reversing. My right bracket was torn in two. My truck runs smooth as silk with this new mount.

Pros
  • Best in its niche
Cons
  • Fair

Revainrating 3 out of 5

Typical cheap Chinese engine mounts.

Replacement engine mounts for Ford F150, F250 and F350 pickups with 5.0 and 5.8 liter V8 engines (several years). Although these mounts are very close in shape and construction to the original mounts, they use 20% lighter steel plates and have inferior workmanship than the original mounts. , on the Westar mount it is only 0.145 to 0.152 inches. On the Original Equipment mount, the base plate that touches the frame mount is .120" thick. On a Westar mount it is only 0.097 inches thick. With the…

Pros
  • Nice to use
Cons
  • High price