Header banner
Revain logoHome Page
🖨️ winsinn ht ntc100k extruder thermistor for printers logo

🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers
img 2 attached to 🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers
img 3 attached to 🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers
img 4 attached to 🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers

Description of 🖨️ WINSINN HT NTC100K Extruder Thermistor for Printers

✔️Upgrade HT-NTC100K Thermistor: package temperature measurement. Head diameter: 3mm, Head length: 15mm. ✔️The temperature measurement: -50 °C ~ +350 °C, can replace the original K-type thermocouple temperature. Fit for printing high-temperature filament. ✔️Adopts 304 stainless steel, with the internal temperature package to ensure the maximum service life with precision temperature measurement. ✔️HT-NTC100K thermistor adopts white high-temperature cord, can bear higher temperature. And for customers' convenience, the wires adopts line connection, the customer can tear the wires depends on their application. The high temperature line is double thicker than others in the market, not easy to break off. ✔️Made by WINSINN. Can be used with the New Sensor Heater Block (Temperature measurement can be up to 350 degrees).

Reviews

Global ratings 3
  • 5
    0
  • 4
    1
  • 3
    2
  • 2
    0
  • 1
    0

Type of review

Revainrating 3 out of 5

They work when installed.

parts are working as expected. The problem with the parts is that the wires from the MoBo to the hot end aren't long enough and the connectors to connect the wires to the MoBo won't work without special tools. I ended up using the original. Wires and soldered the connector from MoBo's original wires to connect the sensor. When I finished everything worked perfectly and I can replace it with a fast connection. It's just not an easy setup. Either the wires need to be longer or a crimping tool is…

Pros
  • ✔️Uses 304 stainless steel with an internal temperature pack to ensure maximum durability with accurate temperature reading.
Cons
  • New competitors have appeared

Revainrating 3 out of 5

There is no data sheet and does not appear to match any standard Marlin chart

They work and the design is good. Unfortunately they don't match any of the standard high end Marlin tables. If you use them at 200 degrees they will probably work for you using the standard NTC100K charts, but the temperatures vary by about 5-10 degrees and they will vary further and further as you go up. This is fine if you enter per-thread settings. The actual temperature doesn't matter as long as you just experiment and find the right setting. However, if you rely on manufacturer…

Pros
  • ✔️The HT-NTC100K thermistor is fitted with a high temperature white wire that is capable of withstanding higher temperatures. And for customers' convenience, the wires use line connection, customer can break the wires according to their application. The high temperature line is twice as thick as others on the market and not easy to break.
Cons
  • Something else

Revainrating 4 out of 5

Requires custom calibration, but works fine once dialed.

Although they are sold as 3D printer components, they may not match the printer firmware's thermistor profiles closely enough to be useful. In my case I got the actually measured temperature around 150 degrees. C when the printer thought it was 210. Even simple filaments like PLA are difficult to print if they are barely softened and not melted. If you're using firmware that understands Steinhart-Hart values (e.g. Klipper), here are the parameters I need to work with - this should help you get…

Pros
  • ✔️Temperature measurement: -50°C to +350°C, can replace the original K-type thermocouple temperature. Suitable for printing with high temperature filament.
Cons
  • No automatically