16Ft Vincos AN6 Nylon & Stainless Steel Braided Fuel Hose + 6An Fitting Kit For Leak-Free Oil & Gas Transfer Review

surprised by the quality of the hose good amount of Steel effusion in to the hose doesn't have a cheap feel the braidings is nice and tight it doesn't just unravel. The fittings are of good quality also .not surprised most of the big name fittings come from China. These are just unbranded. and go together really well

Sections of my fuel system that used this hose started to leak after about 1.5 - 2 years of use. I ran only E85 with this hose and leaks started to spring up at different sections, at first I thought it was a bad install at the AN fitting, which I fixed quickly. Then it happened again on a different area except this time the leak was coming from a crack near the middle of the hose, and after inspection, the hose felt quite hard, so that’s when I began to suspect that the hose is failing. Then…

Got this kit in a pinch on a drag car , worked great for my sniper efi no leaks . fittings are a bit thinner material then say , earls, aeroquip, color fittings brand , some others but it worked and yes 2 more 90 elbows would be great.

This is the same run of hose. this is what I found when making a cut. I'm glad I found this before a 10k motor went lean due to leaks on a car that I'm restoring. Now I'm out 3 to 4 hours of labor.

Used these line on my project car and within a week, part of the line developed a hole right in the middle of the fuel line itself.only ran 93 through it, extremely pissed off because I now have to take it all back out and run new lines. If I could give negative stars I would.DON'T BUY THESE LINES!

Well packaged and well made kit. This Kit is NOT PTFE hose. Do not use for fuel line or high pressure power steering lines.

Fittings are horrible quality. Hose will not properly feed into the fittings without fray and damage, causing leaks. Used vibrant and Russell fittings and they work perfectly on the hose. Would not waste time or money on this product again. Horrible product

Very pleased with this kit. It was purchased to plumb a transmission cooler and remote mount filter in a Jeep XJ. I I had to also order some fittings to interface the transmission and the filter mount, but this kit took a lot of guesswork out of the project and gave me some options when configuring the layout. Several other sellers sell hose in 10' increments. This setup completely replaced the factory cooler and lines so the 16ft of hose was very desirable. I had a few fittings and about 5' of

Only after watching a video from a different supplier of the same/similar product that I found out that when twisting the fitting onto the hose, you do not turn it the way you would when tightening a bolt - the threads are reversed so that when you tighten the other side of the fitting, the entire coupler & hose is pulled together.Some instructions would have been nice as I had written a scathing review on this product only to later find out when shopping for a replacement that the way i was…

the fittings all leak air! Sitting collecting dust now.Dont buy these fittings they are cheap. Mine have already faded with the sun so no more red and they constantly just get loose and leak. But the best part is I had one just come apart and throw all my oil everywhere. And they were professionally installed the right way. Save your money and yourself a headache.

The kit ships in a well packaged box with a nice assortment of fittings. The nylon braided line appears to be high quality. The fittings are a strange "not quite but almost exactly -6" in size. You can't use a -6 wrench on them but a 3/4" will do.

I’m using this to replace some old rubber fuel lines for an LS swap. The hose ends are a bit easier to get assembled than the stainless braided lines I’ve done before. Parts have a nice quality feel to them, don’t really need the 180 fittings, a couple more 90s would have been preferred, but the price is right.

Nice product.you guys should swap those 180s for 90s though no one's gonna use those and I needed 2 other 90s The hose may be prone to expanding or contracting under different pressures, leading to variable performance and unpredictability!

Have plumbed 3 or 4 transmissions with this kit. Past few year's. Good selection of fittings. No universal kit can accommodate all transmissions. Fittings into your specific transmission case will vary. Once you have those fittings your golden with this line kit.

Great quality. I compared the fittings to similar Russell, Earls, and other name brand fittings that I have, and they’re all the same fit, finish, and quality.