Header banner
Revain logoHome Page
🔳 efficiently craft precise 90-degree cuts with the 6pack imperial straight square cutter logo

🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter Review

5

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.5
🔧 Milling Accessories, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter
img 2 attached to 🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter
img 3 attached to 🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter
img 4 attached to 🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter

Description of 🔳 Efficiently Craft Precise 90-Degree Cuts with the 6Pack Imperial Straight Square Cutter

1.Four flutes produce a better finish than fewer flutes. 2.Material: HSS ; Imperial Units, not Metric . 3.One Set of end mill bits Including: 6 Different kinds of Inch Size:1/8",1/4",3/16",5/16",3/8",1/2" end mills to meet your need. 4.Hardness of metal for above HRC 45 degrees,with high bending resistance and abrasion resistance, exclusive to HIGH HARDNESS, HIGH SPEED CUTTING applications. 5.End mill bits are suitable for side milling, end milling, finish machining, etc. Apply to carbon steel, alloy steel, die steel, tool steel, cast iron, titanium, aluminum, etc.

Reviews

Global ratings 5
  • 5
    4
  • 4
    0
  • 3
    0
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

Good Cheap End Mills

Pretty good end mills. Because of their low cost, they work great with wood, plastic, and soft metals. Haven't tried it on steel but they are good for light work.

Pros
  • 4. The metal hardness is above 45 degrees HRC, with high bending strength and abrasion resistance, exclusively for HIGH HARD, HIGH SPEED CUTTING.
Cons
  • I vaguely remember

Revainrating 5 out of 5

Good looking bits at a moderate price but only for soft materials

very sharp blades , but they cannot do the job I bought them for, even when coolant is used the grooves are burnt out. I would recommend using them on wood or soft metals.

Pros
  • 5. End mills are good for side milling, face milling, finishing etc. For carbon steel, alloy steel, die steel, tool steel, cast iron, titanium, aluminum etc.
Cons
  • upgrades

Revainrating 5 out of 5

It is actually

I don't know why but other sellers sell metric end mills as Inch end mills, which is problematic when accurate measurements are required. These end mills are actually imperial, which is a good thing. They cut aluminum very well.

Pros
  • 5 inch end mill. The end mill is suitable for side milling, end milling, finishing, etc. It is suitable for machining carbon steel, alloy steel, die steel, tool steel, cast iron, titanium, aluminum, etc.
Cons
  • Expensive

Revainrating 5 out of 5

Good fit and finish in every way.

They look great although I haven't had a chance to use them yet and am still waiting for the chuck to fit my router and bit holders. Will definitely test them out when my R8 cartridge comes out. After the arrival of the R8 stock liner I have several orders.

Pros
  • 3. A set of end mills Including: 6 different inch sizes: 1/8", 1/4", 3/16", 5/16", 3/8", 1/2" will be yours Meet requirements,
Cons
  • Quick guide