Header banner
Revain logoHome Page
🎛️ precision control: stepless adjustable potentiometer for smooth forward, brake, and reverse operation logo

🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation Review

3

·

Terrible

Revainrating 1.5 out of 5  
Rating 
1.7
🔌 Electrical Controls & Indicators, 💡 Industrial Electrical

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation
img 2 attached to 🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation
img 3 attached to 🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation
img 4 attached to 🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation

Description of 🎛️ Precision Control: Stepless Adjustable Potentiometer for Smooth Forward, Brake, and Reverse Operation

♕【Regulate Range】 Input supply voltage: DC 10V-55V; Maximum current: 60A; Continuous current: 40A; Speed range: 0-100% ; Control frequency: 15KHZ; Apply to: DC Brush Motor. ♕【Switch Function】The PWM DC motor speed controller come with switch function. High power speed controller switch which is much more adaptable and conveniently change the motor direction. ♕【Excellent Heat Dissipation Performance】 The enclosure of the speed controller for motor is an aluminum enclosure. Aluminum shell is very strong to prevent damage, holes on its side and top which are helpful for heat dissipation. ♕【Easy to Operate】The stepless motor controller has a simple potentiometer knob adjusts the motor speed from 0% ~ 100% smoothly. And with LED display is accurate to show 0 ~ 100% of the motor speed. The input voltage of PWM motor speed controller should be equal to the rated voltage of the motor within 10-55V,or it will be burnt. ♕【Application】 The dc motor driver can be used to brush motor speed regulation, light dimming regulation in the DC circuit.Note: The motor cannot be used in electric vehicles.

Reviews

Global ratings 3
  • 5
    0
  • 4
    0
  • 3
    0
  • 2
    2
  • 1
    1

Type of review

Revainrating 2 out of 5

does not correspond to the nominal load.

It was easy to install and from all the information it should work on my 24vdc. Current 20 A. Collector motor with a power of 500 W. It took less than 10 minutes at 1/3 speed. This can be done with a lower powered motor or at intermittent intervals rather than continuously.

Pros
  • Brackets and accessories
Cons
  • Slightly torn

Revainrating 2 out of 5

Very fragile block for mounts and accessories

Passed two of these on a (small) 20# trolling motor and they are too fragile in my opinion. The wires are very small, aluminum? Two simply unscrewed, the wire melted when soldering. The device has stopped working several times, can cool down and work again. I saw some other similar comments and referred to the DROK device. Got it and it seems a lot more reliable, albeit without reverse gear or LED. And you will strengthen the case and insert the fan. Luckily I like tinkering around and studying

Pros
  • Tools and household items
Cons
  • Not sure

Revainrating 1 out of 5

The FWD/Rev switch failed after a single use.

I bought this to replace a broken PWM 60A/100A to power my trolling motor. Thrust 36 lbs, max thrust 30A. First one I bought, the main unit died but at least I got a few uses from it. This one I installed to replace the previous one and I used it ONCE before the FWD/Rev/Off switch died. I measured the side of the motor leads with my volt/ammeter and saw no current when turned on. I measured the terminal side of the battery and saw the current so I knew the battery side was fine. Luckily I had…

Pros
  • Motors
Cons
  • No Power