Header banner
Revain logoHome Page
๐Ÿš€ maximize precision and speed with creality original assembled capricorn 3d logo

๐Ÿš€ Maximize Precision and Speed with Creality Original Assembled Capricorn 3D Review

3

ยท

Average

Revainrating 3.5 out of 5ย ย 
Ratingย 
3.3
๐Ÿ–จ๏ธ 3D Printer Parts & Accessories, ๐Ÿญ Additive Manufacturing Products

View on AmazonView on ะฏM

Media

(1)
img 1 attached to ๐Ÿš€ Maximize Precision and Speed with Creality Original Assembled Capricorn 3D

Description of ๐Ÿš€ Maximize Precision and Speed with Creality Original Assembled Capricorn 3D

It's 100% Creality Original. Upgrade with Low Friction Capricorn Original PTFE Tubing 63CM. Less friction means more responsiveness, less retraction, more accurate prints, less slippage, wear, and tear on the extruder, and less clogging when printing chunky filaments such as some woodfills or ironfills. Lower retraction means time saved every time the extruder retracts. Over the course of a print, a few milliseconds here and a few there add up to a lot of time saved. Capricorn tube is far superior to the white PTFE tubing supplied with most 3D printers. Its much smoother to feed filament through. And when printing it reduces the drag on the extruder giving a much smoother travel and print quality.

Reviews

Global ratings 3
  • 5
    1
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

Works great, installs very quickly

The new hotend took only two minutes to install and worked fine on the first warm-up test. The only criticism is that no mounting screws were included. Probably most people already have them, but I've come back to this hotend after using an E3D V6 setup that doesn't need the old screws. I most likely threw them away, which of course is my own fault. The product is as described, the extra screws were just wishful thinking. Luckily I had spare parts. In any case, the product works great and takes

Pros
  • Less friction means more responsiveness, less pullback, more accurate printing, less slippage, extruder wear and less clogging when printing with coarse filaments like some wood or iron fillers.
Cons
  • Some bugs

Revainrating 1 out of 5

Don't waste money. The quality isn't there.

Bought and installed. This item was poorly assembled. The prints were outputting incorrectly and upon rollback the entire build was found to be leaking through the top of the hot block. This was due to the factory bolt moving away from the plate to the manifold. And the main heating pipe was not screwed in properly as specified. The filament dripping from the assembly resulted in the entire head being covered in Pla filament up to the manifold. Not to mention it invades projects, leaving blobsโ€ฆ

Pros
  • Less retraction means time saved each time the extruder retracts. In the printing process, a few milliseconds here and a few there add up to a huge time saver.
Cons
  • Some little things

Revainrating 4 out of 5

Nice exchange but missing PC4-M6 at the end of the extruder.

I bought this build because I didn't want to mess with the electrics to replace the hotend and fans. I was hoping it was just plug and play. For the most part they are, but they don't include a small pneumatic connector (pc4-m6) for the extruder. So I had to pull out the old bowden cable. It worked on one squeeze, which came out great, but on the second squeeze and the next two after that, the connector wasn't holding the new Capricorn Bowden tube, it was pushing it further out. So I suspectโ€ฆ

Pros
  • This is 100% original.
Cons
  • old