🔧 [UPGRADED] Ultra Durable W10712395 Dishwasher METAL Rack Adjuster Kit Replacement by Blue Stars - Exact Fit For Whirlpool Kenmore Dishwashers - Replaces W10250159 W10350375 AP5957560 W10712395VP - Buy Now for Enhanced Dishwasher Performance! Review

I have changed these adjusters 3 times in the top rack of the dishwasher. In the end I went for the metal ones which seem to be much stronger. One problem was that the wheels on this replacement were too big for the rails. I fixed it by changing the wheels off my old adjusters. See photo - Remove both wheel sets and save all bolts/parts - Remove the plastic centers from the wheels of the new adjuster and the metal washers/bolts from the old set - Insert the plastic centers into the old (smaller

First of all it was delivered quickly BUT I would not buy it again. The instructions are almost useless. All the images are so blurry that they cannot be understood. You get T-20 for 4 propellers. It is no problem for me. The problem is that 2 of the screw holes had a protrusion in the middle blocking the holes. I had to drill them out. One of the holes wasn't drilled deep enough, I had to drill this hole deeper. Stand adjustment does not work. It does not hold the rack in the raised (higher)…

Instructions are a bit lacking and pictures are almost useless (diagrams would be better) but once you work them out it's actually a very easy install - 5 minutes per side, including old part removal. Note that the removal part is actually what takes the most time - the instructions only say to remove the old hardware, but don't indicate if you will be reusing hardware. . You will not. The casters, caster assembly and height adjuster have been replaced so there is no need to carefully remove…

Works great, fits my model as promised - fairly easy to install - took about an hour and spent most of the time figuring out how to remove the original parts. Make sure you place the raising and lowering mechanism between the fourth lower bars and not the upper bars. I made a mistake and had to figure out how to remove and reinstall the two permanently attached pieces - fiddling with them through the bars as some of the steps are irreversible, I also had to fiddle around a bit with the lowering

We really liked our Kenmore Elite dishwasher in every area except for the upper basket support mechanism. The OEM mounts were heavy, well-molded plastic, but the front nylon(?) rollers came loose at the attachment point. I've bought an "improved equivalent" twice that looked exactly like the original but didn't work in the same place. I guess I'm overloading the top basket or twisting the rollers moving it in or out. Regardless, this time I went with the metal shelf positioners that Kenmore…

Factory wheel adjuster broke - no doubt a common problem so the replacement was changed. The kit arrived quickly but one wheel was broken on delivery. Fortunately, the old wheels are identical to the spare wheels, so they can be easily swapped out like new ones. Installation proved less difficult than removing the old regulators; less than half an hour from start to finish. Tools: Torx #20 screwdriver, flathead screwdriver (to remove stock adjusters) and Phillips #2 screwdriver, only required…

I wanted to pull the trigger and buy the replacement direct from Whirlpool. When I got to their delivery area. something clicked and said. Hmm, try Revain as it should cost me around $90. IMPRESSIVE. .what is the price difference. It was less than half the price and looked the same. But it came at a price upon receipt. I like the fact that I saved money for the role. But there are problems with the installation. I think the average regular homeowner might have problems too. First there was an…

1.) The manual is one of the worst I've seen, with images of such poor resolution that they are unusable. 2.) Videos of the manufacturer replacing these parts (Kenmore, Whirlpool, etc.) are much more helpful. BUT 3.) Rack height adjusters WILL NOT WORK if you assemble them according to written instructions or videos; Your stance just stays in the down position. The thumb levers MUST be tight or the mechanism will not rotate properly under pressure for the dual height adjustment to work. I have…

I rarely give good reviews but I feel others need to know what they are getting at. Firstly the product arrived quickly which is a plus but once I received the product and started the repair I encountered the first buying issue which was that while this was supposed to be an exact replacement for my dish rack adjusters it was a completely different design. That in itself is not a problem, because as long as everything works, I don't care if it's designed differently than the original part…