Header banner
Revain logoHome Page
freedom county atv 42 1037 polaris logo

Freedom County ATV 42 1037 Polaris Review

4

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.3
💪 Performance Parts: Shocks, Struts & Suspension, 🏎️ Performance Car Parts & Accessories

View on AmazonView on ЯM

Media

(2)
img 1 attached to Freedom County ATV 42 1037 Polaris
img 2 attached to Freedom County ATV 42 1037 Polaris

Description of Freedom County ATV 42 1037 Polaris

Fits Ranger 500 4X4 09-10, 700 4X4 09, 800 4X4 EFI & Crew 10-14, 800 6X6 10-14, 800 XP 12, 900 XP 13-14, 900 Crew 14, 900 Diesel 4X4 11-14. Fits RZR- 570 EFI 12-14, 800 08-13, 800-4 10-13, 800S 09-14, 900XP 11-14, 900-4XP 12-14, 900 Brutus HD 13. Fits Sportsman 550 11-13, 550 EPS 10-14, 550 X2 10-14, 550 Forest 11-14, 550 Touring EPS 10-14, 550XP 09-10, 850 Forest 11-14, 850 Touring EPS 10-14. Fits Sportsman 850 X2 11, 850 XP 09-13, 850 XP EPS 10-14, 850 SP 15, 1000XP (built before 8/24/14), 850 Touring EPS HO 13. Fits Scrambler 850 HO/EPS 13, 850 XP/HO/EPS 14, 1000 XP Built before 8/14/14.

Reviews

Global ratings 4
  • 5
    3
  • 4
    0
  • 3
    0
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

A quality replacement part for your Polaris Ranger or UTV

Purchased for the Polaris crew, these parts have proven to be cost effective parts. That's how many games the factories had. https://youtu.be/quHNPj5sVTs?list=PLOqvKi40if-KiKFwgblX1z0oqGxS4DFJt

Pros
  • Stylish and modern design
Cons
  • Available in white only

Revainrating 5 out of 5

Fits better than OEM replacement parts

is better than OEM because the top of the ball joint does not have the Welch connector found on most OEM joints. This plug is usually the cause of all ball joint failures because once they fall off, anything and everything leaks into the joint. They are sealed very well and you will keep coming back to them.

Pros
  • One year trial
Cons
  • Quality of

Revainrating 5 out of 5

Satisfied and works as a good alternative to OEM.

Mounts on the Polaris RZR 900 XP4 on the upper and lower forearms. Pretty close to OEM except for the size of the retaining slot. The groove is a little smaller, but the stop bolt goes in tighter. When pushing in the indexing bolt, make sure that the groove is correctly aligned. If you hammer on a screw, you will damage the threads. The installation went very well. Haven't had any problems with these yet. A good alternative to OEM when you need parts quickly.

Pros
  • Rugged Construction
Cons
  • Non-Automatic

Revainrating 2 out of 5

They are ok.: Shock absorbers, struts and suspension

They are ok. They seem to fit snugly around the hands. The boot is very elastic, thick and beautiful. Production feels inconsistent, some very tight and difficult to move like you'd expect from a new ball joint, and the other two felt much weaker, almost half-worn right out of the box. My biggest concern is the locking ring/clip. The clips are too small for the groove on the ball joint, or the groove is too large leaving space between the lever and the clip. This can cause the ball joint in the

Pros
  • As far as satisfied
Cons
  • I will write later