Header banner
Revain logoHome Page
🔪 titanium coated high speed lepohome cutter for improved performance logo

🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance Review

3

·

Poor

Revainrating 2.5 out of 5  
Rating 
2.3
🪚 Industrial Drill Bits, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance
img 2 attached to 🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance
img 3 attached to 🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance
img 4 attached to 🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance

Description of 🔪 Titanium Coated High Speed LepoHome Cutter for Improved Performance

【Widely Used】Perfect Step Drill Bits suitable for drill holes in various material: within 3mm/0.12 inch (Iron Plate, Copper Plate, Aluminum Plate); within 5mm/0.2 inch (Wood, PVC sheet, Insulation Boards). Not suitable for hard and brittle materials such as stainless steel, glass, tile floors, walls etc. 【Material】HSS combined with a titanium coating. More capable and durable. 【Easy Drilling】Two-Flute Design for smoother cutting. High Step design let you feel the stop and never drill bigger in mistake. 【SET INCLUDES】Bit #1 (5 steps): 4-12mm (4mm, 6mm, 8mm, 10mm, 12mm); Bit #2 (9 steps): 4-20mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm); Bit #3 (15 steps): 4-32mm (4mm, 6mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm, 26mm, 28mm,30mm,32mm). 【Package Included】 3-Piece HSS Groove Step Drill Bit (4-12/ 4-20/ 4-32mm ). 1/4" Hex shaft drives are suitable for all kinds of for home DIY power drills.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

DO NOT buy from Cutting Tools

All 3 of my bits were too big for the 1/4" quick release. I was able to adjust it to about 1/8". I was in a dilemma so I tried it and it couldn't even open the hole before it started to burn. When I looked again at the attachment, it had gone a little deeper into the shaft, but still not far enough to snap in. It was so tight that I had to use other tools to remove it. I then checked the other 2 bits and encountered the same problem. All 3 went in the trash. Don't waste money.

Pros
  • Industrial & Scientific
Cons
  • Expensive

Revainrating 5 out of 5

They do the job exactly as expected.

This is a specialty tool for me I think most of you that don't work in guitar pedal shops or anything. However, it does not have to be the most durable product. It only needs to be available when I need to make sure I'm drilling a large hole of the exact size. I'm sure if you tie this to a very powerful tool and drill through metal with it all day you can probably mess it up, but I really don't see any reason why the average Joe would need parts like this to have any more imagination than that…

Pros
  • Cutting Tools
Cons
  • weak

Revainrating 1 out of 5

umm, right? - industrial drill

where to start lol. First, I've never seen a titanium coating wear away during the first few turns of such a tool. Second, the 1/4" shank was out of tolerance. I put it in Milwaukee, it actually got stuck in there. Third, I used my good TEMO bit to make the first hole. I bought this set, because some of the holes need to be bigger. So most of the work got done down to 20mm or so. I had to go down to 24 or 26mm. This tool didn't actually cut the metal it smeared it. The biting edges didn't do…

Pros
  • metalworking and universal drill
Cons
  • write later