💡 HYKOLITY Dimmable Daylight Recessed Downlight: An Effective Lighting Solution Review

These bulbs are just great. If they last as long as they're supposed to, they should outlive me and I'll never have to climb stairs again. They are bright, easy to install, fit perfectly in a standard glass and look very neat on the ceiling. You are working on a dimmer that we already had in the diagram. I couldn't be happier.

I installed 12 of these hooks - the hooks that come with the kit and are supposed to hold the light are NOT working properly. Lights hang from the ceiling. A sealer is required to stick it to the ceiling and close the gaps where air enters. The lighting is very bright and the dimmer works great. They fade quite a bit, which I like a lot. There is no flicker in the last 3 days of use.

10 out of 12 bulbs work fine, 1 has a broken switch that selects light temperature and 1 keeps flickering. You have a quality control issue. Customer service seems non-existent, no one answers online chat or answers the phone. They also disabled the typical Amazon ability to contact the seller. I plan on returning all the lights, it's just too much work to remove 10 from the high ceiling. Update: After the review was published, the seller got in touch and all defective light bulbs were replaced

I received the headlights quickly and they were exactly as described. They were easy to install and I am very happy with the color and brightness. One of the lights didn't work. I swapped the light over to make sure it was a light and not a recessed can. When I tried to get a replacement from Amazon my only options were to return them all or keep the faulty light and make it shorter. However, I left a review about the product and the seller contacted me immediately. They offered to send…

I bought a set of 12 12 Watt 3000k Warm LEDs to replace recessed downlights. They were easy to install after removing each filament shield. Simply pull down on the decorative ring to reveal the metal supports, then pull the supports together to release the device from the glass. The lamp's porcelain base extends from the top of the casing. The new LED light is screwed into the existing porcelain plug and then the metal supports of the new LED block are put back in the same place as the old…

The idea of having multiple color/temp choices was very appealing, especially for the price. I bought 24 of these to install 22 at my mother-in-law's house (2 extra for future mishaps). I installed 17 of these today and decided not to mess with the install anymore after all the headaches. In the first box of 12 I had two with broken switches and three that didn't look like 4000k despite setting them up. Three looked warmer than the others and were brushed aside. Luckily I had enough in another…

These lights are pretty good for the price. Installation was fairly easy and most sane people should be able to install it without too much trouble. No tools were required for my installation. I simply removed the covers from the old lightbulbs, unplugged the outlet, and pushed in the metal tension tabs. I took the optional step of attaching the base to the top of the jar, but that's not necessary. Then I screwed in the connector and connected it to the new light. I also used a magic eraser to…

I'm a construction worker and I do house renovations. The customer wanted to upgrade their recessed lights with Daylight. I uninstalled the first one and tried to install a new one. It doesn't stick to the ceiling. It took me a minute to realize that the spring was not up to standard. I've never seen a spring bar made like this before. The problem is visible in the photo. The light does not go up all the way because the spring detaches from the spool. In order for them to work, the glass has to

The wire on the spring clips is too thick (much heavier than traditional can rings) to slide over the guide grooves - they pop out every time the light is about an inch from the ceiling. Also, each side of the spring clip is a separate piece of wire so they are not in the same plane, which is different from standard spring clips (made from a single piece of wire). I tried all sorts of adjustments - spread the wires further, loosen the screw on the plastic tabs and bend the wire. If I come…

If you put them in 5 inch jars they're great. Wonderful. 5 Stars. But if you put them in 6-inch jars, you're going to have trouble. The tabs that the springs attach to have two latches, and by default they go into the farthest latch. You would think it would be 5" on the inner mount and 6" on the outer mount, right? nope If you measure the springs on the outer detent, it's 5 inches. So you need to loosen the set screw and push the springs all the way out (where there is no detent so the springs