Header banner
Revain logoHome Page
🔧 kipa r12t fuel filter water separator 120at npt zg1/4-19: complete combo filter for automotive racor r12t, marine diesel engine, outboard motor - durable spin-on housing (10 micron, 3/8 inch npt fitting) logo

🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting) Review

7

·

Average

Revainrating 3 out of 5  
Rating 
3.1
🛢️ Fuel System, 🏎️ Performance Car Parts & Accessories

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting)
img 2 attached to 🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting)
img 3 attached to 🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting)
img 4 attached to 🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting)

Details

BrandKipa
Product GradePerformance Part
Outer MaterialNylon
StyleSpin-On

Description of 🔧 KIPA R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19: Complete Combo Filter for Automotive Racor R12T, Marine Diesel Engine, Outboard Motor - Durable Spin-on Housing (10 Micron, 3/8 Inch NPT Fitting)

This spin-on filter design is simple to replace and the reusable clear nylon collection bowl and features a self-venting drain for removing unwanted muck and water. Notice: This a separator for Diesel & Water, It could not be for Petrol & Water separator, R12T Fuel Filter Water Separator 120AT NPT ZG1/4-19 with Fitting Complete Filter Assy. Filter is designed for high performance applications, and with flow rate of 30 GPH on the R12T model, your engine will perform better than ever with clean, water-free fuel. Don't be caught in the water without one of these diesel spin-on filters. Fuel Water Separating Filter fit 3/8 Inch NPT Outboard Motors as well, 10 micron filters are over 90% efficient at removing particles as small as 10 microns. 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems, Designed to trap the smallest particles and emulsified water from gasoline. The filter units are coated with a durable electrostatically applied powder coating for superior corrosion resistance,instruction: 1.Nylon collection bowl down when installed the water separator and filter. 2.This filter has four ports, two inputs and two outputs. We provide two plugs for the extra two ports. If you need to use two plugs, you must install them to the filter and tighten them. 3.Before installing the filter, you have to remove those plugs, teflon-tape them, and re-install them.

Reviews

Global ratings 7
  • 5
    3
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    2

Type of review

Revainrating 1 out of 5

Looks Good: Fuel System

Similar to Racor but no quality. This is a typical Chinese POS. The fittings are flimsy, short and cheap. And yes, "the flow will not stop".

Pros
  • Best in Niche
Cons
  • Not Reliable

Revainrating 5 out of 5

Good quality seems to be best for spare parts

Be sure to remove the filter and put a few drops of oil on the other ring. Otherwise, once installed on the boat, you will never take it off again. I had to clamp the case in a vise to loosen it.

Pros
  • . Lots of positive vibes
Cons
  • Almost never

Revainrating 5 out of 5

Fits just like my old Parker

The seam on this product fits and works just like my old Parker fuel water separator. It's a long, cold winter and I won't be out on the water until April catching Northern California salmon, rockfish and halibut. I will use this for a petrol outboard.

Pros
  • Very good value for money
Cons
  • Functionality

Revainrating 5 out of 5

Great replacement filter for small diesel engines

Bought to replace a broken and often problematic fuel filter on my Kubota tractor. Fuel filter upgrade/replacement. It has a large capacity and a better water separator with a better water drain valve. I wish I could point out some negative points just to be fair but honest; I didn't experience anything on this project.

Pros
  • Certified
Cons
  • Hard to tell

Revainrating 3 out of 5

Buy your own accessories. The filter is excellent.

Filter works great having bought quality NPT fittings. I recommend buying the filter separately, not the kit. I'm not familiar with the barb fittings, but the NPT plugs in the kit are not airtight. Tried several times with various pipe thread sealants, but without success. I bought a second set of filters thinking I overtightened and snapped the thread. No, the candles were still flowing. Bought high quality NPT square plugs and they sealed on the first try. The other two fittings received an…

Pros
  • Weight
Cons
  • No Automatic

Revainrating 2 out of 5

The bowl cracked in less than a month of use

the white plug at the bottom of the bowl fell out and gas went all over the back of the hull thank goodness this boat has a safety system that when the The fuel system loses vacuum, fuel pump cuts out, I tried putting it back in place but it wouldn't tighten, I took the filter off and looked at the bowl in bright light and I can see the crack running from top to bottom goes. guards and spread it wide enough to prevent the connector from being tightened. All I did after installing the separator…

Pros
  • few competitors
Cons
  • so-so

Revainrating 1 out of 5

Good price and delivery

I installed this on a boat to remove water from the fuel and when the booster pump was turned on it ran into the filter canister. I figured it might just need a bit of depressing, but I checked before installing it and it was tight. Well, it turned out to be tight because the threads grabbed where the canister attaches to the cast. I suspect this is due to the canister screwing onto a threaded bushing molded onto the mount. It is likely that the aluminum threads will get stuck in the upper…

Pros
  • Sturdy construction
Cons
  • Frequency