ErGear Gas Spring Arm Wall Mount for 17 to 32 Inch Screens - Height Adjustable and Extended Up to 18.3 Inch - Fits Multiple VESA Mounting Sizes Review

I was a little apprehensive about installing this on drywall but the instructions were clear and I had the right tools to do it. Drywall anchors are not recommended, although I suspect you could if you had heavy-duty anchors. I mounted directly into the stud. Be careful when drilling the pilot hole as you could knock the screw out of position and tilt the bracket. The gas weight adjustment is a great feature to adjust the movement to the weight of the monitor being held.

Overall a decent monitor arm for a 17lb 32in monitor. I bought 2 for monitors side by side. I sit on one and stand on the other but need vertical adjustment to move the monitors up and down. I am deducting 1 star because the vertical adjustment is not 11 inches as shown in the picture. I measured the 8 inch vertical adjustment from the lowest to the highest position and it is generous. Another problem I've encountered is that the tilt function screws keep loosening when the monitor is moved…

I bought two of these monitors to flank my nearly sunken center monitor. The attachment to the studs is much sturdier than the C-clamp used in most other mounts and it solved my problems with a flat table. I was able to line them up perfectly with minimal effort. I love everything about the product itself and the only reason it loses a star is because it is packaged in a very dangerous way. It is packed with large spring tension. and fastened with a zipper. When I opened the first one, it…

Perfect? No not true. Will it hold my $1,100 monitor without fear of falling? Yes. Once you set it up properly and tilt it, you'll almost never move it again unless you move it away. In this case, being able to get the screen out of the way is a brilliant plus for a monitor setup. If you can install your monitors, do so. I can't believe I didn't do this many years ago. The table looks much tidier and has a lot more space. The mount seems to snicker a little when you touch it, which is very…

Liked the wall mount monitor mount but installation was awkward as the washers provided were too small for the VESA mount when using M4 VESA screws and VESA Use extension brackets. I had to put my own washers in. If your monitor's VESA mount uses M5 or M6 screws, there is no problem. If your VESA mount doesn't require extension brackets, no problem. However, if your VESA mount uses both M4 screws and extension mounts, the screw heads will be smaller than the mount holes and the included washers

I really like this monitor mount, but the tilt mechanism has a design flaw that causes the monitor to slowly tilt forward over time. No matter how hard I tighten the screw on the tilt mechanism, the monitor slowly tilts forward over time. or whenever I adjust my arm. Each side of the tilt mechanism has a plastic washer and a metal washer. Removing the plastic disc from one side of the mechanism solved the problem. If that doesn't work I will replace the washer with a lock washer. This keeps the

it's fantastic! durable, moves beautifully and stays right where you put it. I'm so happy I bought it. The only thing I have is that in certain positions the hands collide, unfortunately this is the position I want it in most of the time. He doesn't like being low and close to the wall. the plastic cable guide hits the other arm in this position, knocking it off and disconnecting all cables. but that's probably not a problem for most people. the solution would be to set it lower so it's not at…

I really like this monitor mount, but the tilt mechanism has a design flaw that causes the monitor to slowly tilt forward over time. When I tighten the screw on the tilt mechanism, the monitor slowly tilts forward over time or with each adjustment of the lever. Each side of the tilt mechanism has plastic and metal washers. Removing the plastic disc from one side of the mechanism solved the problem. If that doesn't work I will replace the washer with a lock washer. This keeps the monitor from…

The monitor arm is well designed, with sensible adjustments and thoughtful cable routing features. There are no complaints. However, there is one glaring downside. The specs state that it supports monitors weighing up to 17.6 pounds. No, that is not so. Well, the lever itself handles it easily, but the tilt mechanism certainly doesn't. I installed a Philips 328E1CA (15.2 lbs) and the tilt mechanism didn't even come close to keeping the monitor upright no matter how tight I tightened it. Tie…