Header banner
Revain logoHome Page
💎 enhanced precision with oscarbide engraving sculpturing composite multilayer logo

💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer Review

6

·

Average

Revainrating 3.5 out of 5  
Rating 
3.7
🔧 Milling Accessories, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to 💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer
img 2 attached to 💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer
img 3 attached to 💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer
img 4 attached to 💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer

Description of 💎 Enhanced Precision with OSCARBIDE Engraving Sculpturing Composite Multilayer

☆Up Down Cut,1/8" Shank X 1/8"Cutting Dia, 22mm Flute Length with 2 Spiral Flutes, Total length 45 mm, 5 pieces per pack. ☆The Unique Flute Design makes cutting process easier and faster, Smooth Cutting Without 2nd polishing process, ALTIN-Coated Improved the bits service life. ☆Due to the Great hardness of solid Tungsten carbide, it provides excellent abrasive and wear-resistance, Bits Stay Balanced during High Speed rotation process. ☆Fast Chip-Removal volume and Speed, Non-stick With bits, Suitable For Composite multilayer board, hard wood, polywood, acrylic. ☆Double Flute Spiral Solid Carbide Up-Down Cut End mill Router bits are widely used For CNC Engraving, Milling, Roughing, Hollowing, 3D sculpturing purposes.

Reviews

Global ratings 6
  • 5
    0
  • 4
    4
  • 3
    2
  • 2
    0
  • 1
    0

Type of review

Revainrating 3 out of 5

Leaves a clean cut on thin plywood

I've been looking for a compression cutter (straight down) to cut thin plywood (1/8" and 3/8") and they worked great. Nice clean cut at a good price!

Pros
  • Excellent overall performance
Cons
  • Minor issues

Revainrating 4 out of 5

Incompatible Bits Between Lots

This is the second set of these bits that I have ordered. The first set for me went through about 80 tray cut outs, this set didn't go through 5 trays. All 5 broke within 5 minutes, same exact settings as before and same wood.

Pros
  • New
Cons
  • Quick Instructions

Revainrating 4 out of 5

Doesn't work well with Oracle.

Definitely a cheap product that works well overall. The mask layer above doesn't seem to work very well. I wouldn't recommend this if you plan on layering over your notches. A straight router seems to work well on most woods, but I've found it acts like a straight router on MDF. Spend a little more money and get a little better.

Pros
  • Confident
Cons
  • Some issues

Revainrating 3 out of 5

Disgusting cutting action.

Not a clean cut at all. Combination jets like this should produce clean bottom and rim edges, but I have more breaks at the top than a regular vertical cut jet and too much vibration travels through the fiber. Played around with feeds/speeds to no avail - the edges still looked awful. I'll take that as a lesson learned and stick with my more expensive beats.

Pros
  • ☆ Double Helical Spiral Carbide End Mill Top Down End Mill Milling cutters are commonly used for CNC engraving, milling, roughing, gouging and 3D sculpting.
Cons
  • High price

Revainrating 4 out of 5

Small Hard-to-find bit at a reasonable price

Detects 1/8-inch bits that exceed 1/2 cutting inches is not easy. They are 22mm long so they will cut through 3/4 inch thick material if you don't press too hard. They solve the problem of the top of the plywood peeling off and the cuts in hardwood are very clean on the top too. Haven't used them. long enough to know how long it lasts. The price for a pack of 5 is also good.

Pros
  • ☆Unique groove design makes the cutting process easier and faster Smooth cutting No 2nd polishing process ALTIN coating Longer bit life
Cons
  • Very expensive

Revainrating 4 out of 5

Doesn't suck dust MDF

I bought these to Cut 3/4 inch MDF pieces. And they made clean cuts. However, they did not remove sawdust from the cut line and left dust in the kerf. I kept an eye on the cut with a vacuum and a pickaxe to remove the dust before the next pass to avoid burning and smoking the bat. Up to 1/2 inch of dust came out easily. It was the last quarter inch he entered. I was expecting the "top" part of the drill to come out, but perhaps because MDF produces dust rather than chips, it didn't work as…

Pros
  • ☆ Cut up and down, shank 1/8" x 1/8" cutting diameter, flute length 22mm with 2 spiral flute, total length 45mm, 5 pcs packed
Cons
  • Some bugs