Pressure 90 125Psi Compressor LF10A 4H 1 NPT1 4 90 125 Review

Makes our old air compressor work like new again! We got a cheap air compressor from Harbor Freight and within a year the switch broke (and we didn't have additional insurance) and we had to add a custom spring to the on/off switch to keep it in the correct position. Then we did some research and found this on Revain. amazing at such a cheap price. installs it. and voila! works better than new. I think the price of this control switch is actually lower than the compressor insurance price. Thank

Bought to replace a light weight version of this switch of the same design which I took apart and couldn't put back together. For the sake of good and decency, never take this switch alone. it will fall apart into a dozen pieces and the spring tension on the assembled block is tremendous/impossible to get back in place during a fight. NEVER disassemble them. one. With that warning, this replacement works perfectly, it was shipped and arrived very quickly. I had to deduct 1 star because of the…

I installed this on an old Campbell Hausfeld 8 gallon compressor with a bad switch. I removed the Campbell-Hausfeld switch/regulator assembly and hooked up the Lefoo pressure switch with no problems. The switch has 1/4" female outputs in all orientations and I used one for the tank, one for the output, one for the poppet and one for the gauge. I had to lower the setting to 100 pounds to prevent that the click blows out.This gave me a pressure range of 100 pounds off and 80 pounds on.The…

I bought this to replace the original switch on my Makita MAC5200 compressor. As far as I can tell this is a higher quality part at half the price of an OEM part. I also appreciate the large holes in the metal case that the wiring runs through. They are ideal for standard 1/2 inch cable clamps. In my case I replaced the 6 foot 14 GA power cord with a 15 foot SJOOW 10 GA cord. doesn't look like they'll be very effective either way) and used the aforementioned cable clamps to mount it, as well as

I bought this to replace a faulty pressure switch on my Ingersoll-Rand 2475 two stage compressor. It was essentially a plug and play installation. It is modeled after a Furnas/Hubbell 69JF9LY pushbutton switch so the contacts are in a different location under the cover, but the pilot is in the same location as the IR compressor and there is a removable rubber plug on each side to allow the to allow wiring. The element is obviously made in China, so it might not last very long, but at about a…

My tradesman's compressor was leaking and needed this switch, among other things. This is a solid replacement for a product that comes with a four port manifold. Whatever you do, never disassemble this switch, ever, because the chances of you putting it back together are almost zero percent. I removed the four screws from the distributor and the entire switch fell apart. It is much better to remove the old manifold from the compressor. I only took off one star because the design of these…

I bought this switch for an old Campbell Hausfeld supercharged Craftsman air compressor that was made in the USA. The switch that came with the supercharger cut off at 135psi, which is higher than I needed, and loaded the supercharger to get the last 10 pounds. Since the derailleur would not adjust, I decided to replace it with a new 125psi cutout derailleur. I was hesitant to buy a Lefoo switch as an OEM replacement costs around $100. But I couldn't justify the cost of a used compressor that…

Warning - yes, spelled wrong! - The pressure drops to 90 before turning back on - You can adjust the two screws I showed in the picture. It says 125 psi max for the switch but the left screw says to raise the low and high limits and most people want it to turn on closer to 105 because you can't get some tools at 95.4,3, Can operate 2 and 1 psi. Haven't adjusted the screw yet where it lifts both of them but the switch works fine so far - THIS IS THE GOAT'S OILED ROPE TO WORK AND WOULD NOT WANT…