Circular saw Makita 5008MG, 1800 W blue/silver Review

Soft start set 2-pin to 20A. Works great. It should be connected to the break in the wire between the switch and the motor. There is an empty space in the handle, just right for a soft starter. If you connect a soft start to the saw, then it will not work: the light will not work. Soft start it starts smoothly when turned on, not the engine.

It took a long time to choose how everyone here actually does it. I bought this model for cutting plywood (1 cm in two layers). Pila did an excellent job. Sawed 16 sheets in 3 hours. He let me rest after each cut. Of the minuses, like everyone else writes, there is no soft start . it really picks up, but this is not critical. We launch in advance and drove to cut.

Has pros: The assembly is excellent. Liked the trigger. When starting, you feel the power, kicking. Different cons: Short cable. On the old Makita 4 meters. There is not enough soft start.

An excellent device, I took it from a friend for work, I liked it and decided to take the same one for myself. Comfortable and functional. I advise you to purchase!

In general, I am satisfied with the purchase of shares 8889 re, I think this is the norm. As for the warranty card, they said that they would send it . we'll see

I took it for installation in a table and I'm thinking about a circular for mobile work, but after such a diameter (210 mm) it will be sad to cut with a small disk. Its pros: Powerful - cuts everything like a knife through butter. The presence of illumination. The quality is top notch. Nice disc included. Has some cons: It is, of course, heavy and this must be taken into account. Do not run with it, holding it in your hand on weight.

Wonderful saw. Pros: It has been working for more than a year, without any complaints. Strong, molded sole, powerful engine, good long cable. Cons below: The only negative, of course, is that the Makita does not have a guide rail under it.

Unedged board OAK 50 mm with ease, smoothly and quickly Undoubtedly an almost flawless saw - the perfect balance of weight, power, smoothness There are small flaws. Some pros: Powerful Balanced Soft as a foreign car :) sawdust removal is flawless When released, the disk protection does not hit hard and ring, but softly hits with a special rubber band The ground is flat Native disk super for rough tasks Its cons: Price Too heavy Disk protection always interferes, does not open - infuriates Site…

It should be noted that the "Makita" tool has a good cooling system on the tools, retribution requires systematic maintenance, but these are the working moments of the revision, everyone's business. Pros below: An excellent hand saw. Before that, I had experience using the Interskol saw 2 kW, which has been serving properly for 9 years to this day, the anchor was changed, I didn’t look after the builders, they dissolved the boards and gave it coke. As for this device, I liked the even saw cut…

In general, the saw is not bad, before that it was Hitachi for 10 years of intensive use, I only changed the brushes, once I had to change the anchor Got pros: Powerful, minimal backlash, illumination of the cutting area, easy replacement of brushes, Its cons: Due to the lack of a separating plate behind the saw, it can clamp the workpiece, it is not very convenient to unscrew and clamp the ruler

The saw fully performs its functions. There is enough power to work on a full departure of the disk. Completely satisfied with the purchase.

The saw itself is powerful, but when sawing 50 dry boards, I want to add power to it. And so it’s a very good saw, I recommend it, I don’t advise you to take a less powerful one if you need to cut thick wood.

I decided to buy a saw that was more expensive and more powerful, since the previous tools did not please me at all with their price-quality ratio. Here I am happy with everything. Power can be envied, money was not thrown away. I haven’t noticed any shortcomings yet, even my wife, who is indifferent to tools, liked my choice

Has some pros: I took 190 after Interskol, also a decent saw, but this one moved from a Soviet car to a decent foreign car, soft high-speed start, easy, everything is regulated clearly, easily and reliably. Different cons: Of the shortcomings, if this power cord was four meters, it would be.

I recommend this product to everyone! You will not regret! And pay less attention to reviews forever than dissatisfied! You can't please everyone! Sometimes they take a Makita 2470 puncher and hammer window openings with them, then they are perplexed how so . Got pros: Quality tool! There are no problems with spare parts, everything can be taken from the catalog on Makita Pro! Build quality, ease of use! Satisfied with everything! Cons below: There is none of them! Many write that there is no…

It is very pleasant to the touch, there is no backlash, I can’t say about reliability, time will tell Has some pros: I see no reason to repeat them, they were already called before me and more than once Some cons: Not revealed yet. If only the price, since this is no longer the same Makita that it once was. Alas, China is China ((

I put a disc on aluminum, sawed a used board, with nails, sawed it in two, carces of nails (Soviet 200ki) fell apart calmly, without hesitation. I tried to screw the nozzle for the vacuum cleaner - heaps a full pouch or pocket - unscrewed it. You can say silent, there is no “hysterical screech of an eternally dissatisfied mother-in-law”))))))) does not cut the ear)))), the cut line is blown, always visible, translucent. The model is very successful, it does not throw up at startup. I RECOMMEND!

Although it’s the first circular saw, it’s very easy for me as a beginner to cope with it, the weight affects a little. Cutting soft wood without straining a little slows down on the knots, but it goes like a tank, except for pine saw nothing. The disc, in my opinion, is an excellent cut, it turns out clean. there haven’t been any adequate blows yet, the absence of a riving knife is not noticeable, when sawing it doesn’t clamp anything and doesn’t interfere with work. I don’t know how anyone…

I haven’t participated in serious work yet, I just managed to test it on the balcony . Blowing off sawdust works so that the vacuum cleaner gets little, chips are everywhere)) it cuts wood and chipboard without smelling an opponent). I tried to make a double wash down on a chipboard, it didn’t work out, when adjusting the disk to the depth of the wash down, the disk (or platform) shifts, this may lead the mounting bracket itself to the side, I think it can be fixed .) I don’t use parallel…

I tried out a Resanta 2 kW at 5500 rpm before deciding to buy this one, and it was a great saw. Features-wise, the Makita 5008 is a step down from the competition at 1.8 kW and 5200 rpm. But in practice, I find that the same Makita substance makes far easier work of cutting. High grade engine and cutting element, in my opinion, have an impact.