🚗 Red Hound Auto Molded Mud Flaps for Chevrolet GMC Colorado Canyon 2015-2020 (w/o Flares/Cladding), Heavy Duty Front Rear 4 Piece Set Guard Splash Compatible Review

Put on my 2016 Colorado and they look like they're in. Easy to put on and hold up very well. No warping or discoloration after sun exposure and numerous automatic washes. I am very happy with this purchase and would recommend these fenders.

I like the fact that these fenders are significantly cheaper than Huskies and Weathertech. The instructions were easy to follow. Make sure you have a T-15 bit for your 3/8" drive so you can get all the screws out. As for the front, I rotated the wheel as much as possible to get the best access. I didn't like the idea of drilling a hole in the wing, but with the extra propeller the flaps are very secure. The flaps look great!

My fenders came faster than expected, great! I went ahead and started installing them and it was very easy for my 2016 Chevy Colorado. The holes were where the screws were. The only thing that didn't fit were the rear fenders. Just a hole that was at the inner end, the last hole. But that's not a problem, it fits right into the other three holes. The hole I had to drill wasn't a problem either. The isolation worked well. I recommend them for my truck guy.

Fenders as advertised. They are perfect for my 2018 Colorado. The bolt holes lined up perfectly and I was able to use the factory bolts to attach the fenders. I'm hesitant to drill holes in the fenders of my new truck for fear of rust; However, the seat of the factory screws was so tight that no more holes had to be drilled. They are bigger and heavier than I expected. They're so big they're almost out of proportion for a mid-size truck and would look right at home on a full-size truck. I'm…

Excellent quality flaps. Rugged plastic construction, standard optics. The fit on my 16 Canyon was perfect and installation was a breeze. You will need a T15 Torx bit to remove and reuse the wheel arch bolts to install them. I just pushed it into the 1/4" socket with a 1/4" ratchet (with a small piece of paper to hold the bit in the socket) and removing and installing all 4 fenders was in done in about 15 minutes. max. There are mounting points at the top, but they have to be drilled and aren't

These are very good fenders for the price. Make sure you try to match the front to the front. You are marked. Once we got that done, installation was a breeze. At the top of each is a spot where you need to drill a hole in your truck if you want to use that hole for a screw. We didn't, and they seem to stay pretty without them, even after a few trips to the car wash. I had an issue with my tires splashing water onto the side of the truck as I pulled out of the car wash, ruining the car wash and

they fit. i will give it to you I didn't worry about the transparencies on the truck's paintwork. I had a real bear time with one of them. The wheel's felt pad does not hold the u-clamp/nut close enough for the factory bolt to cut into it. I tried for 45 minutes! Finally he grabbed it. Keep in mind. The included screws are very soft! Hold the drill firmly to avoid tearing off the head. I made that mistake. The vise is finished because the screwing has already started. I agree with others, the…

This item matched the description. The material is heavy. Each unit is perfectly matched to the contour of the wheel arches. The mounting holes perfectly match the mounting bolts on the truck that hold the original wheel arch covers. For each block, a new hole had to be drilled in the top of the block at the edge of the wheel arch. The instructions called for drilling a 1/8 hole for the included mounting screw, but I found a 5/32 bit and hole worked best. It took me about 30 minutes to install…

Advantages: Looks like factory The 3rd screw is not really needed. Works well and has held up, after 3 months they still look great. Cons: 1. The supplied bolts, while longer, do not match the thread pitch of the factory bolt, so are not interchangeable. 2 The factory bolts are almost long enough to be used with ease. Hour to get to the screw hole and finally pull the thread through.3. The supplied screws are not made of stainless steel. I live in Georgia and have never seen road salt and yet…