Header banner
Revain logoHome Page
πŸ” high precision 2.5 inch table inserts (pack of 3) for 14" band saws & scroll saws - ensure perfect fit logo

πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit Review

3

Β·

Average

Revainrating 3 out of 5Β Β 
RatingΒ 
3.0
πŸ”© Power Tool Parts & Accessories, πŸ”§ Power & Hand Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit
img 2 attached to πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit
img 3 attached to πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit
img 4 attached to πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit

Description of πŸ” High Precision 2.5 Inch Table Inserts (Pack of 3) for 14" Band Saws & Scroll Saws - Ensure Perfect Fit

Three inserts to protect your expensive blades Please measure your saw as some Delta & Rockwell &Grizzly14" bandsaws has slightly smaller holes for the throat plate. If so some slight filing or sanding may be required.If you mind, please don't buy it. use on 14" Band Saws and 24" Scroll Saws. 2&1/2" X .100 thick Please measure your saws recess to ensure proper fit They fit Delta, Rockwell, some Jet, Ridgid, Grizzly, and other imports. Make sure your insert recess has the locating pin on the side, not on the rear. IMPORTANT INSTALLATION NOTE:I have sold several hundred of these and occasionally someone will have the problem of it being a bit too large. First make sure the lip of the hole is free from dirt. If a table alignment pin,is not tight or missing,often the blade mounting slot will close up some over time which reduces the insert hole diameter slightly. I tap a flat head screw driver into the blade installation slot a bit to wedge it open. That should spread the insert hole enough for it to fit.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

had to file the edges

They didn't fit the 'hole' of my Reliant bandsaw I'll have to file the edge a little No problem but they didn't fit 'perfectly'.

Pros
  • Three inserts to protect your expensive saw blades Please measure your saw as some Delta & Rockwell & Grizzly 14" band saws have slightly smaller holes for the needle plate. Some filing or sanding may be required in this case. Don't buy this
Cons
  • Empty

Revainrating 3 out of 5

Bought for Grizzly 14 Bandsaw G0555

Need to replace my insert for the above bandsaw. Had trouble finding a complete insert that said it would fit a Grizzly bandsaw. The inserts work, but you'll have to file them damn well to fit the table. It's also about 1/16 inch below the table, so it looks like there might be some clearance issues. I'll probably have to pick it up to straighten it. They work but they aren't perfect, it's probably better to get one from Grizzly as they will most likely fit unmodified and the price is similar.

Pros
  • Make sure the locating pin in the recess of the insert is on the side and not the back
Cons
  • Update Availability

Revainrating 1 out of 5

Poorly made and doesn't fit.

Good sensor; The finish is good but they are TOO BIG for my 2" and 1/2" slot on my desk. That means they are made too big. They're not that big, but as anyone who works with a bandsaw knows, "not much" makes a big difference. Maybe it was truncated to 2 1/2 and the growth happened during the finishing process, which is like engineers designing a library but forgetting to take the weight of the books into account. Since only one of my 3 packs was shrink-wrapped, I suspect 2 other people found…

Pros
  • is used on 14" band saws and 24" spiral saws.
Cons
  • Some small things