Header banner
Revain logoHome Page
yonico 12249 router 2 inch 2 piece logo

Yonico 12249 Router 2 Inch 2 Piece Review

4

·

Average

Revainrating 4 out of 5  
Rating 
3.8
🪚 Router Bits, 🔪 Cutting Tools

View on AmazonView on ЯM

Media

(4)
img 1 attached to Yonico 12249 Router 2 Inch 2 Piece
img 2 attached to Yonico 12249 Router 2 Inch 2 Piece
img 3 attached to Yonico 12249 Router 2 Inch 2 Piece
img 4 attached to Yonico 12249 Router 2 Inch 2 Piece

Description of Yonico 12249 Router 2 Inch 2 Piece

These bits cut shaker rail and stile cabinet door frames at a depth of 3/8" in stock up to 7/8". They feature 1/2" shanks and come in a wooden box. Create rail and stile cabinet door frames. Premium C3 micro-grain tungsten carbide blades for a sharper & longer lasting edge. For use on table mount router. Silver induction brazing for maximum strength and durability.

Reviews

Global ratings 4
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 5 out of 5

It would be 5 except.

Ordered and received on time. Both nozzles came in a nice wooden box. They were needed for the project so I used them right away. Or at least tried. The first cutter worked great, but on the first pass with the other cutter, the shank broke just below the cutter head and the cutter flew through the shop. There was a nice dent in the drywall, but luckily that didn't happen, it didn't hit me. I have never seen a shaft broken like this and I hope I never will! I sent the kit back and received the…

Pros
  • For use on bench router
Cons
  • Fits

Revainrating 1 out of 5

Great product would definitely recommend

They fit me perfectly right out of the box, nice box too, I have a Sears Mini Shaper, 7/8hp. I was able to raise them above the minimum mark, after a few test runs found the right height and went to town, I assembled 17 doors in 5 hours. Not as fast as a commercial setup, but not worth the $400 either. I was working with pine so I expected the ends to snap a bit and they might have been perfect for hardwood but my budget required I use what I could afford so it's pine. The sharpness was…

Pros
  • Make closet door frame with rails and rods
Cons
  • Cord is shorter than other picks

Revainrating 4 out of 5

If that sounds too good to be true. You were right

Don't waste your money! I thought it was too good to be true and I should have known! Pros: The packaging is VERY GOOD! Beautiful wooden box suitable for presentation. Yes. Cons: Blades are not sharp. The first attempt left a lot of wool. Coping was just awful. All sorts of bits and pieces. Seems to be a balance issue. Lots of vibes. The nuts weren't tightened, I agree, but really? In addition, the diameter of the top and bottom wrappers is critical. If they are not sanded properly, the…

Pros
  • For use on a desktop router
Cons
  • Slightly wrinkled

Revainrating 5 out of 5

Good tool, good value for money.

Just caught myself looking at a Freud Shaker that will replace my trusty Yonico. Fairing cuts. Maybe time to replace? Then dawned I've had really good results with my current set and why switch now as this is my latest closet makeover.I used my old set to do a lot of things for our Florida apartment including new kitchen cabinets, a kitchen island, floor to ceiling dressers , a large vanity table and a large double bed with lots of doors and drawers. These puppies ran hard. If I need to replace

Pros
  • These bits cut screed and cabinet door frames from 3/8" to 7/8" in stock. They have a 1/2" shank and come in a wooden case.
Cons
  • alt