Header banner
Revain logoHome Page
zento deals pieces load resistors replacement parts logo

Zento Deals Pieces Load Resistors Replacement Parts Review

6

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.5
🔋 Starters & Alternators, 🏎️ Performance Car Parts & Accessories

View on AmazonView on ЯM

Media

(4)
img 1 attached to Zento Deals Pieces Load Resistors Replacement Parts
img 2 attached to Zento Deals Pieces Load Resistors Replacement Parts
img 3 attached to Zento Deals Pieces Load Resistors Replacement Parts
img 4 attached to Zento Deals Pieces Load Resistors Replacement Parts

Description of Zento Deals Pieces Load Resistors Replacement Parts

✺CONTROLS CURRENT FLOW- The Zento Deals 6 Ohm 50W LED Load Resistors will control the current flow in electrical circuits. It will put a specific amount of resistance into your LED lights to make it function properly because LEDs uses less energy than your regular lights. ✺FIXES LIGHT ERRORS- The Zento Deals 6 Ohm 50W LED Load Resistors will fix your LED lights problems such as blinker flash error, no flashing or burnt out bulb indications, hyper or error flashing of LED turn signal, parking / driving running light or license plate light. ✺HIGH QUALITY- The Zento Deals 6 Ohm 50W LED Load Resistors is made of high quality materials to sustain a long lasting usage. ✺EASY INSTALLATION- The Zento Deals 6 Ohm 50W LED Load Resistors is easy to install, just connect one wire to ground and the other wire to the turn/brake wire. Please apply the provided quick wire clip so you don’t have to cut any existing wires. One Load Resistor is required for each turn signal bulb. Note: LED Load Resistor will get hot, therefore, please don't mount the LED load resistors on plastic, hoses or painted surfaces. ✺UNIVERSAL- The Zento Deals 6 Ohm 50W LED Load Resistors will work on any vehicle and can be connected across the turn signal bulbs or License Plate Lights to simulate the load of a regular filament bulb (2 Amp load).

Reviews

Global ratings 6
  • 5
    3
  • 4
    3
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Works great on alternators and alternators

They are good but a bit big. However, they work well. I think they should be a stackable solution. A resistor that plugs into an outlet and a light that plugs into a resistor.

Pros
  • Decent performance
Cons
  • No instructions

Revainrating 5 out of 5

Skip this step, buy an LED turn signal.

Installed on my 2002 Explorer, placed it on a corner, hyperflashed. Installed on both corners. The turn signals stayed on. Went and got an LED turn signal. Problem solved. Skip a step, get a flasher.

Pros
  • Delivery was very quick
Cons
  • Only available in black

Revainrating 5 out of 5

Hot. HOT! HOT! in alternators and alternators

These things get HOT! Make sure they are not near plastic or painted bodywork. Especially if the headlights they are in are on all the time. Be careful not to melt plastic and zippers. I had to run additional ground wires to prevent hyper flashes on my C6.

Pros
  • Pleasant to use
Cons
  • I vaguely remember

Revainrating 5 out of 5

Excellent purchase, quality and price.

Love the quality and simplicity. It would even be a great buy if it came with exact fitting hex head screws. Instead of quick couplings. These connectors are not to be used for SAFE extended use or PROFESSIONAL installation.

Pros
  • Sturdy construction
Cons
  • Lots of stuff

Revainrating 4 out of 5

Resistors were as described and worked properly

Worked exactly as I hoped. Just make sure one end is connected to the power side and the other end is connected to the ground side of the light. The fast flashing turn signals were annoying and these resistors did the trick and I got 4 extras. Fast delivery and just what I needed.

Pros
  • One year trial
Cons
  • Protection

Revainrating 4 out of 5

Double check cable

It worked fine but you may need instructions to install everything correctly. My 2004 La Saber has 3 wires coming from the lamp socket. One to the ground, one to the turn signal and one to the parking light. Watch an online video to make sure you have turn signals and ground connected. I used the red clips that came with it, but you have to pry the wire off the side of the car before you can insert the bulb wire into the clip. I would remove the metal contact when putting the clip on as the…

Pros
  • GOLS certified
Cons
  • Some errors