6 Pairs 12" Full Extension Side Mount Ball Bearing Sliding Drawer Slide, 10", 12", 14", 16", 18" & 20" Lengths Review

Great price, slides seem well made, instructions are worthless but I didn't need them. Only issue is the slides seem a little stiff and hopefully loosen up over time; even with the drawer removed the slides they are still stiff. The drawer I made has a 1/2 inch space on each side and the slides are listed as 0.47 inches wide. However, my caliper reads 0.52 so I had to adjust for the difference and they still are a little tight.

UPDATE (7/11/2020): It’s been a week since I corresponded with the seller about the not packaging enough screws. The seller was quick to respond and asked for my mailing address indicating that the replacement screws would be sent with a tracking number as soon as the warehouse sends it to him/her. As of today, I have no messages or any indication that anything was sent. I would recommend the drawer slides still as they are a great value. However, plan on buying extra screws if you want to…

I ordered the 16" drawer slide set of 6. When installing them, one of the slides had an issue with the metal over the ball bearing bending. Luckily I only needed 4 sets. Once installed, they worked great. I contacted the seller and within a day got a response. They shipped me a new set of 6 even though only one had issues. Would definitely buy from them again

A very good quality drawer slide. They were easy to install and very well built. They came with all the mounting hardware.

I bought these because they were cheaper than same type of slides I used from Lowe’s. The price was good and They were easy to install. But 1 drawer wouldn’t close. Ball bearings fell out and holders were bent. Didn’t discover until installed. Replaced with extra set.It happened again. Went to Lowe’s bought moreexpensive set that I had used on another project. No issues. Drawer slid in and out perfectly so I concluded these slides were the problem.

These were exactly has described. We used them for a desk we made for our granddaughter. She was absolutely thrilled with how quiet and smooth they were.

I thought it was a just a bad slide when the bearings came out of one of them, but when it happened twice, I knew these were not going to be the slides I was going to be putting in my builds. Luckily, this wasn't a build for a client. imagine if it broke right after I sold it, that would have been even worse.All of the slides on amazon look like they're made from one manufacturer and there is a design flaw.I'm going to have to look somewhere else for different design of slides made by a…

Ordered the 6 pcs 12" slides with fasteners which arrived very quickly. The first impression was substantial mass in a little box.6 pairs of slides were individually packed in a poly bag, about over 76 screws in a small zip lock bag, together under loops of plastic wrap. My previous drawer slide purchase was with the cheap powder coated white slides with plastic rollers. I remember them being expensive. But these are heavy duty, nearly 2" in height and full extension, not to mentioned priced…

Great value for money. Even though the over all width says 0.4” plan for the standard 0.5” gap min between the cabinet and the drawer. Fit like a glove with no issues. As a previous buyer stated, if you are planning on using these on drawers that are less than 0.75” use your own screws.

These drawer slides were easy to install and work great. They are made of high quality materials. Very smooth glide. I wish they were sold in smaller quantities as well. Bought another brand because I only needed 1 pair. It was not made as well as this brand.I highly recommend you purchase this brand of drawer slides.

This my second experience with these slides. As before they are easy to install. Work well. Good quality. Work as well as higher end - and more expensive - slides I’ve used.

Was looking for a solid drawer slide that wouldn't break the bank. Would have loved to install the top of the line name brand slides but these fit the budget much better and seem to work very well. This type of slide is touchy to install properly as the drawers need to be square and the slides need to have the correct clearance on each side of the drawer, these are no different than any other slide of this type in that regard. They are a good value for the money and operate very well, they lock

Building my first vanity with slides, so had to experiment with positioning slides. Some trial and error. Not thrilled with the bumpers at the slide ends, seems like I will have to push the drawers to fully close,but don't have drawers installed yet.

I don't want to hate on these slides, but I built a custom mudroom cabinet system for a client and decided to save a bit of money and use these slides, and I'm not impressed with them at all. I got them to work, and hopefully they will hold up, but I had one fall apart on me while installing it. The balls in the slides literally fell out. I used them on 4 drawers and got them to all work, but they weren't the best experience.They don't slide as smooth as your nicer more expensive options. So if

These are good. They work fine and are very inexpensive. Overall quality 3 stars, but at this price a solid 4 stars. Thanks for attention.

The sliding draw works ok, I had to add some grease to some of them to work better and the step back is that doesn't include the hardware.

I used 3 pairs of these for custom built drawers and they work great. I'm really happy with the quality especially considering the price. They were easy to install and the drawers slide well.

I liked the sturdiness of this product but the heaviness made them a little more difficult to hold in place while installing. The screws they came with were a little too long to go in the drawer. I had to buy some slightly shorter screws to use on the drawer side.

Used these drawer slides to replace broken one on a set of chest of drawers that were 10 years old. The ball bearing system had broke on the old. These were great replacements and easy to install.

Instructions are awful if you didn’t know what you were doing. They will pop out of alignment with some pressure, but that could be good since the metal did not bend and went right back into place.