ALONEFIRE Offset Flashlight Mount For Picatinny Gun Tactical LED Torch - Sports Outdoors Hunting Fishing Shooting Airsoft Guns Accessories Sights Optics Scope Review

Does not tighten on Bushmaster upper rail. Lock latch Lever eats into main body of mount unit more and more with every use. Springs used inside underneath Groove to release side plate when unlatching are exposed to rail and gouge into rail damaging coating on edge of rail, and it never tightened enough to eliminate wobble on rail.BUT the clamp that holds any accessory DOES hold accessory fairly well.After seeing damages trying to seat and adjust.gave up and returned, never range tested.I do not

Well made but didn't fit the light I ordered, was my mistake. Would recommend, friend bought mine from me for his "kill light" to his AR-15.

At first it didn't fit my light, a little bit of electric tape and it fits perfectly, I love it. Very solid, and was a very good replacement for the other mount I had

Using it forward mounted on my .22 for night hunting. Light hold is solid, fits my Magpul Rails accurately. Aluminum material is adequate for my use.I'd be just little extra careful not to overtighten things with this, it's a light alloy. Great value.

Although it didn't fit my light even with the spacer it, i got it to work. Seems of good quality and the QD function is perfect. I don't understand why they make non QD light mounts.

So I thought this was good till I went to swap my light to another gun. It has a tension pin on the tension arm that will fall out because there is nothing to hold it in but tension and the springs will fall out as well.

The piece of plastic could be more of an acute angle, blocking less vision, but I suppose you could put it on a lower rail. Nice and tight seal, and undoes smoothly, no grit with time. Rock solid frame on the flashlight itself, with size adjusters.

As advertised. Nicely constructed of solid material. Comes with plastic spacers to give your light the right fit. Even though my flashlight has a 1" diameter, it did not fit perfectly until I used one of the spacers.

For the money I have no complaints, a little rework and this will be excellent for the purpose I got it for. The roll pin falls out, and that causes the clamping mechanism to explode. Easy fix, stays together under tension anyway. Other than that the parts are clean and it works. A cheap addition to an even cheaper flashlight for a shotgun that wont serve a critical purpose.

This mount is well made for the price. It does not need to be torqued to much to be secured to the rail. Tighten by hand just enough then swing the lever down. You'll know if it's too tight long before you have an issue like any tension lever like this. Fit my J5 tax light no problem!

Fits perfect on my Radical Firearms upper. Very pleased with the quality of the mount. The quick release lever sure is handy. My LED flashlight is secured tightly it's not going anywhere.

QD lever cams are poorly profiled, leaving the assembly loose when it should be secure. Allen cap screw sockets are sloppy resulting in a poor fit. Low price = low quality = sub-standard performance. This is not a product where you get any value for your money.

Perfect fit and very high quality. Knurled tightening bolt allows easy removal and attachment. The provided plastic shims make fitting each torch an simple and secure task. Highly recommended.

I purchased this to mount a flashlight on my pistol for low light plate shoot. This is not a good fit for a pistol because of the awkward angle that the light ends up mounted on a pistol but it does a great job for plate shoot competitions. However, I can see this being a permanent addition to a rifle and that works nicely. The mount is very light and it is made with good quality. I have bought both the quick release and the screw version and both stay on the pistol without a problem but I…

I will give this only 4 stars till I can get some rounds down range with it. It fits well and seems like it will do the job! It is on my 12ga. now with a Costco 350 lumen light on it. I know neither light or mount are "rated" for heavy recoil but I will mount it on my AR and see if it can hold up to that

I have used this for a while and even after several removal and replacements (which is a super nice feature to have on a flashlight) it still works great. These things are sturdy and simple. Don't get tricked into paying a lot of money just to mount a flashlight

Works great, used it to mount a decaker light onto a Remington 870. So far has worked perfect and has not come loose or anything. Great for the price.

They will not stay tight (but they are inexpensive) wanted a quick release scope, first time I used them, scope fell of in my hands after a few rounds (lucky). Modified them (flattened the locking cam and changed the bolts). So now they will lock down lightly and only need a turn on the bolts to stay put. Ended up with sorta kinda quick release. You get what you pay for

Really a great price very inexpensive it mounted right on the rail of my shotgun with no problem and it's adjustable so it will accommodate almost any tactical flashlight out their

Seems well made but wont't fit any of my flashlights. The bushing supplied is too thick and the mount alone is too big for a good fit on anything I own. Don't be misled.