Header banner
Revain logoHome Page
🚀 upgraded bczamd cartridge accessories extruders logo

🚀 Upgraded BCZAMD Cartridge Accessories Extruders Review

3

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.7
🖨️ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🚀 Upgraded BCZAMD Cartridge Accessories Extruders
img 2 attached to 🚀 Upgraded BCZAMD Cartridge Accessories Extruders
img 3 attached to 🚀 Upgraded BCZAMD Cartridge Accessories Extruders
img 4 attached to 🚀 Upgraded BCZAMD Cartridge Accessories Extruders

Description of 🚀 Upgraded BCZAMD Cartridge Accessories Extruders

Apply to Creal CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Ane A8, Maker Select V2.1, v2, Wanhao Duplicator 3D Printer, V6 Volca MK8 MK9 MK10 Extruder/Hotend etc. Tips: No need any connector, no need other splice things, directly cut the cover skin, decide how length you need, then connect to the board. The improvement compared to ordinary red heating tube:1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful. 2.From the original 40W power to 50W, the maximum temperature increases from 300-31°C to 340-350°C. Can be used with the new HT-NTC100K temperature thermistor. 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.

Reviews

Global ratings 3
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 4 out of 5

Good quality, cable too short for Ender 5 Plus

Got this for the Ender 5 Plus. 1m length is too short. You need the 2 meter version. The connector is also the wrong type (requires JST SM). I use the GulfCoast Robotics All Metal Hotend; Cartridge size is a bit small, I ended up filling the gap with thermal paste (Noctura NT-H1). I ended up trimming the cartridge and adding JST SM 2 pin connectors to use the longer factory line and make future replacements easier. Otherwise, it heats up much faster than the factory heating. Basically I am…

Pros
  • Absolutely amazing!
Cons
  • Not bad but...

Revainrating 5 out of 5

Worth every penny and wakes up the printer beautifully

After almost a year of almost constant printing, my cartridge heater is finally starting to separate. I was getting random system shutdown errors, temperature swings, and the preheat time was getting longer every day. I replaced the stock 40w cartridge with this 50w cartridge and those issues were resolved. The part of the job that takes the most time is threading the wires through the wire harness (about 5 minutes or so), and my printer went from repair to printing in less than 10 minutes…

Pros
  • Easy to use
Cons
  • Quick Start Guide

Revainrating 5 out of 5

Better than series heaters.

Much more reliable and better heat regulation than traditional heaters. With these heaters you will reach the target temperature much faster and more evenly than with standard heaters. Worth the extra money if they came with the connectors installed, but they're great nonetheless. The connectors just make installation easier and quicker, but definitely not a deal breaker. I would highly recommend these heaters to anyone looking for something better than stock, here they are. I've also found…

Pros
  • Few competitors
Cons
  • Unreliable