Pros
- Glass with a sidewall front mesh Allows for dropsy space for connections and a graphics card
Cons
- Cheap and crooked metal Build is quite unsatisfactory. there is no hard drive
Pros
- - Spacious - Good breathability - Glass and not quite thin metal - Enough space for cables under the back cover
Cons
- - Few racks for the motherboard. Such a large body, but regretted the racks. I had to buy a set for 150r - The front bottom fan is difficult to screw on. Could at least put a couple of clamps in order to fix them instead of the lower screws - There are few holes in the PSU casing through which cables could be pulled to the same video card. Of course, it turned out to stretch, but if there were additional holes, then it could be done more discreetly and accurately
Pros
- Appearance, airflow
Cons
- Completely uncomfortable and unreliable case
Pros
- Mesh front panel. The ability to install 3 140 mm fans on the front surface, 2 140 mm fans on top, and 1 120 mm fan on the back, which are not included in the kit, that is, you need to prepare 1 thousand each. for every good fan. Glass side wall. Possibility to install more than 2 hard drives, where 2 HDD 3.5 are installed in the lower basket.
Cons
- In general, in my opinion, this is a budget model on the border of the transition to the middle segment. I really didn’t like the location of the bottom basket, it should be moved closer to the front panel, since the proximity to the installation site of the power supply makes it very, very difficult to install a powerful long power supply with detachable cables. Without dismantling the PSU, you can’t connect the cables, and by connecting the cables, the dimensions of the PSU still increase and it’s even more difficult to push it back into the hole-shelf (it’s still a puzzle). A completely glass side wall, and not a glass window, is not practical, it can be easily broken by negligence, especially since the case was taken for children.
Pros
- Great case for your money
Cons
- In comments
Pros
- performance quality; spacious, plenty of space for pulling cables and in general for the "stuffing"; mesh on the front not fancy design.
Cons
- the above mesh is quite large, and its effectiveness against specific dust pollution is doubtful; knock-out connectors on the rear panel; thin metal; slightly noisy coolers with non-adjustable software backlighting (if you purchase a case with them).
Pros
- - Top for your money! - Spacious cable management; - Quality of materials; - Tempered glass on the side; - Price.
Cons
- - Very close location of the HDD sled to the power supply; - No anti-vibration pads under the HDD; - Inconvenience of fastening the video card to the case; - There is no way to quickly remove the dust filter from the front panel; - Inconvenient SSD mounting next to the cable holes; - Front panel wires look cheap (It's more like a nitpick);
Pros
- Very decent case for your money! Very beautiful and strict appearance, even if backlit. Mesh front! Facade glass on such buildings has completely compromised itself! If you like RGB backlighting and want to save money, then take the case version that already comes with four RGB fans in the kit - Deepcool MATREXX 55 MESH ADD-RGB 4F - this bundle + another 2 thousand, but buying additional fans separately will cost significantly more. You can change the lighting of the fans from the button on the front panel of the case, if you connect it using the built-in molex tail to the power supply connector. A good built-in set of different dynamic highlights. Although I would prefer permanent one-color ones. I do not like connectors for flash drives and buttons on the top of the block! Here they are from the front. A plus is a dust shelf that protects the power supply wires from it, and a basket for HDD devices hidden under it. But because of it, there were some inconveniences, which I will report below. Lots of room for cable management. Sufficiently thick metal even at the side metal cover. Removable plastic grill on top. Possibility to put a dropsy radiator or even additional fans under the top cover of the case. Tempered glass looks great! To be honest, competitors of this level would cost 2-3 thousand more. UP: Here's what else I found from the features in this case. If the backlight of native fans is connected to the molex of the power supply, and not to the motherboard. And when you press the front button, changing the colors and dynamics of the backlight of the fans, I used to wonder why there is no option with the backlight turned off completely. I started experimenting with this button. And found this mode! You just need to briefly hold down this button and the backlight will then turn off completely! ;)
Cons
- As a picky user spoiled by good cases, I will describe in detail what I didn’t really like about it. Sometimes there is a marriage. On a flat table, check its geometric shape for the possibility of deformation during its transportation. Joints of planes for the presence of cracks. The mounting pads for the motherboard are screwed in very tightly. As many have already mentioned, one fastener in the kit is not enough. In other holes, the cut thread is also far from ideal. With great effort, the rear plugs for expansion cards break off. With their buildup for breaking out (and they break out into the inside of the case) - you can safely damage some elements on the mother. Because of this danger, I changed the algorithm for collecting computers in this case. First, I try on the motherboard without screwing it on, then I outline the plugs that need to be dismantled, I remove the motherboard itself from sin, and then I break them out. The retractable bar near these plugs is also not perfect in design. No indication of activity of Hdd-Sdd disks! In the dark, the front USB ports have to be found by touch! Very narrow cable entry holes for 2.5 SATA SSD drives. If the power supply has rigid power cables, it will not be easy to connect them. It's easier to connect the wires first, and then screw the drives themselves. Not a very long niche for placing a power supply with a large bundle of wires. So much the worse if the "box" of the block turns out to be non-standard, for example, longer. If it were possible to dismantle or temporarily remove the HDD basket, it would be much easier. But the basket is on fixed rivets. And what prevented you from moving the basket a little further from the feeder? It is better to dismantle the lower dust filter for the power supply immediately, it clogs very quickly, and few people clean it often enough. Single color blue power button. It would be more logical to make it at least neutral, with a white backlight. The illumination of the fans under the mesh at the place of its fold on the right side does not look very harmonious.
Pros
- Excellent purge! of the body due to the mesh in front. Easy assembly! in this case, you can even assemble a top-end system. Lots of space! for laying wires at the rear wall. The strong case on a bend, iron holds perfectly.
Cons
- Missing 1 motherboard holder. 8 out of 9 Grid dust collector on top with magnets, you need to think a little. it is not always convenient to screw a video card, also modify it. It is necessary to expand the holes for the SSD space a little, the wires rest a little.
Pros
- Price No backlight Strict appearance
Cons
- Inconvenient Assembly
Pros
- High-quality case with good ventilation, space for cable management and excellent appearance. For my money (bought for 4000) - no complaints at all. 100% Satisfied
Cons
- Didn't find it during use. Unless - placing the SSD in the inside of the case, and not the outside, where all the wiring goes, can confuse someone, but here A) You can try and still hide them at the back B) Use M.2 SSD-shniki
Pros
- Side wall - glass
Cons
- All the rest
Pros
- Well ventilated and that's about it.
Cons
- I'll write in the comments
Pros
- Design, good quality materials, inexpensive. Glass, not plastic transparent on the side. Comfortable dusters. Lots of space. I don't think you can find better for this price. Corps - Fire! )))
Cons
- There are no shortcomings, there are minor quibbles, which have already been discussed here more than once. For me, the main drawback was the lack of built-in coolers - the toad choked me to buy separate ones))). When installing a 140mm cooler at the top front, there may be problems - for me, for example, the front wall did not snap tightly into place, since the socket with wires rested against the cooler. Middle and lower 140mm installed without problems. So pay attention to this moment. Of course, you can put coolers on the inside of the frame, but somehow it's not very beautiful. There is no HDD indicator, the power indicator could be dimmer, a non-removable disk pocket, some kind of crooked thread for MP racks - well, this is all insignificant.
