Header banner
Revain logoHome Page
๐Ÿ”ง fel-pro ms 98003 t intake manifold gasket set" - "fel-pro intake manifold gasket set ms 98003 t logo

๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T Review

6

ยท

Excellent

Revainrating 5 out of 5ย ย 
Ratingย 
5.0
๐Ÿ”ง Gaskets, ๐ŸŽ๏ธ Performance Car Parts & Accessories

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T
img 2 attached to ๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T
img 3 attached to ๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T
img 4 attached to ๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T

Description of ๐Ÿ”ง FEL-PRO MS 98003 T Intake Manifold Gasket Set" - "FEL-PRO Intake Manifold Gasket Set MS 98003 T

DESIGNED FOR IMPERFECT SEALING SURFACES -- Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces. STRONG AND DURABLE -- Features molded rubber over an aluminized steel carrier which resists high heat and coolants. SUPERIOR SEAL -- Proprietary rubber sealing beads help eliminate potential leak paths for a superior seal. EASIER TO INSTALL -- Locating tabs assure proper alignment and easier installation. PREVENTS OVERTIGHTENING -- Torque limiters help eliminate overtightening and gasket splitting and extruding. EVERY PART FOR THE REPAIR -- Fel-Pro gasket sets include every part needed for the repair unless otherwise noted.

Reviews

Global ratings 6
  • 5
    6
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Expensive but sloppy

Given the price and quality of the FelPro material, you'd think the packaging would be a little better. As a result of poor quality packaging, my lower intake gaskets were bent.

Pros
  • Easy to read control panel
Cons
  • Doesn't fit all

Revainrating 5 out of 5

Excellent Gasket Kit for GM 3

Excellent Gasket Kit for GM 3.4L V6. There are even different o-rings that you will need. I wish the RTV tube was a little bigger. I still had enough to get the job done. The gaskets themselves are much better quality than the OEM junk I pulled out.

Pros
  • Easy Installation
Cons
  • No Performance

Revainrating 5 out of 5

Without water pump housing O-ring. That .

Without water pump housing o-ring. It contained the intake manifold coolant pipe O-ring. The small RTV pipe included in the kit is sufficient to form the bottom of the intake manifold for the block gasket (physical end gaskets not included).

Pros
  • Economy Price
Cons
  • Upgrades

Revainrating 5 out of 5

My daughter's car repaired

Used this on a 2000 Chevy Impala with a 3.2 engine (3200). Such a superior product compared to what came in their car from the factory. If you have the horrible intake gasket leak that these engines suffer from, buy this gasket kit and you'll be glad you didn't have to buy another car. Installation is not for the timid.

Pros
  • Best
Cons
  • Hard to say

Revainrating 5 out of 5

I'm a big fan of Fel Pro products for .

I've been a big fan of fel pro products for over 25 years. I replaced the intake gasket on my 02 Malibu at about 70k. I drove another 110,000 and the intake gasket failed again. The OEM gasket and the first Fel Pro gasket both had a fabric cage that split and crumbled on both gaskets, allowing water to enter the oil pan. This seal consists of a metal frame. I think if the OEM and first set of Fel Pro pads were made with a metal frame, they wouldn't fall off as quickly, even if the Fel Proโ€ฆ

Pros
  • A sea of positive emotions
Cons
  • Piggy bank Price

Revainrating 5 out of 5

GM 3.1L / 3.4L V6 Intake Manifold Gasket Kit

This is just what the doctor ordered for those of you suffering from horrible LIM seal failure on GM vehicles running 3.1- or 3.4 liter vehicles. V6 engine. It usually appears as a milky oil contaminated with antifreeze. The engine can also overheat. This is due to the physical destruction of the existing OEM plastic and silicone gasket. It lacks the strength to handle the expansion and contraction at the interface between the aluminum cylinder heads, aluminum intake manifold and cast ironโ€ฆ

Pros
  • New
Cons
  • Slightly Torn