Friho 10 Inch Ball Bearing Side Mount Drawer Slides, 5 Pairs Full Extension 12'', 14'', 16'', 18'', 20'' Lengths Hardware Review

18" full extension: They have been installed in a woodshop cabinet only for a couple of weeks so I cannot speak to the longevity, but their construction is consistent on all glides and they are firm with no wobble or slack. No sharp edges and the bearings don't rattle around. I will be ordering some 24" for two more cabinets. I like that they came with screws and instructions. I'll edit if problems develop.

These were such a good replacement upgrade for my old roller slides. Out of the ten I received, seven rolled just right, two seemed to not have enough resistance, and one of them was way too stiff, making it unusable. I do feel for the price they are very decent, and so much quieter than the old ones.

They work. Very bare bones, value slides. No soft stop or self pull in. You get what you pay for. I used them to organize my shop. They do the job. I would go for something better in my kitchen.

These are great slides for the money. They come overpacked with grease, so you have to wipe a lot of it off. I did damage one trying to push the drawer in, they are uber sentive to over tightening. Thankfully I ordered 1 more than I needed! Other than that, the ended up working just as well as the big box stores at half the price.

look great , a bit tougher to install -- built dresser for grandchild but have concerns the slides could pinch ( or worse ) a small child's fingers

Well worth the money. Exactly as described, besides the fact that there were no instructions provided from the manufacturer/distributor. Fortunately, I have installed this type of slide before and there is plenty of instructional videos available online. As I reached the end of installing the last set, I realized that I did not receive the amount of screws needed to install them as I normally would. I ended up going to the big blue box store for #6 countersink screws in 5/8" length. Looking…

Installation was a 'breeze' with the rear-mounting extensions. I ordered five sets of each to replace damaged center-mount glides on my 5-drawer dresser.

I installed 13 drawers into a custom-built wall unit in our bedroom. I repurposed the drawers from our pre-existing dressers, but they had the bottom drawer slide. I was floored when I saw how much side mount drawer slides were at the home improvement stores. I ordered these from Ebay at a FRACTION of the total cost I would've spent elsewhere. I've installed all the slides and assembled all of the drawers and couldn't be more pleased!

I am using these to as part of a project to build in a closet in a house damaged by a hurricane. 8 are installed so far with no problems. If they hold up they will be a great value for the price. Time will tell.

I liked the fact it glides nicely and it is sturdy. I had to put the screws on the different place from the original holes, but insteration was not too bad. I replaced all the junkie slides on my boyfriend’s chest of drawers with it. Now he is super happy.

These are mediocre at best. I went with these because I wanted the black color and they were a little cheaper than alternatives. But the quality is significantly lower than the Promark brand I've purchased for several previous projects. These will suffice if you have a lightweight application that won't get heavy use. But even then, I'd still recommend the Promarks. These don't glide well on the rails, seem poorly constructed, and are difficult connect when replacing removed drawers. I would…

Just installed them on a set of workshop drawers that I made to hold machine tools. Installation was straight forward and operation is silky smooth with a nice locking detent when closed. Units seem well made with a nice silver finish. Maybe not necessary but I substituted larger/stronger mounting screw since these drawers may end up holding a heavier than normal load. No instructions came with the units but it is not hard to figure out how they mount and there is information on the internet on

I was making a wardrobe cabinet with big drawers. These rails look simple and standard but with the weight of my drawers loaded and the gliding motion, these are quality and are lasting.

I used a couple to make a sliding shelf for my PC to make it easier to get to all the cables in the back. I installed it easily, and it works like a charm. Nothing in particular to say about it, just works as advertised and that's all I needed.

I've used the 22" and 16" on several projects and they seem to work fine for about 1/3 the price i'd been paying. Mainly been using them on pull out trays I've made for our kitchen & bathroom cabinets.

I ordered a 16" slide with a 16" extension and planned for that. As delivered they are 15.75 long with a 15.25" extension. Folks, just tell me that initially. I can react to the difference, but I planned and documented for 16".BTW these appear stout enough and well built otherwise. Order before you do your drawings

I'm very pleased with how these drawer slides are working, especially given that they're a bit cheaper than even the cheapest ones you can find at the box stores. I've used them to make a drawer in a small PC stand, and to make drawers for a drill press stand that takes a fair bit of abuse and is used to store scrap metal and such. They're not self-closing or anything fancy, but they do have a soft stop of sorts that also helps hold the drawer closed. I'll definitely be buying more of these as…

If you want a easy install get the kreg drawer slider kit from your local hardware store. There are some reviews that these are cheap but I am here to tell you they are not. Great quality and are heavy duty. I will most definitely be purchasing these again on my next build.

Needed to replace some desk drawer glides I screwed up a couple years ago by mistake. I purchased these to correct my mistake and went way above my expectations. Easy install supplied the hardware needed and were way better quality than ones that come with the desk.

one side of one of the tracks had some ball bearing problems but I got the set of 5 to have a spare. I would definitely buy again for my next project