Header banner
Revain logoHome Page
πŸ”‹ 5-foot fuel line: 1/4" id nbr hose 4 an push on hose engine liner for fuel systems, e85, e10, coolants, oil, air, methanol, lubricant logo

πŸ”‹ 5-Foot Fuel Line: 1/4" ID NBR Hose 4 AN Push on Hose Engine Liner for Fuel Systems, E85, E10, Coolants, Oil, Air, Methanol, Lubricant Review

4

Β·

Poor

Revainrating 2 out of 5Β Β 
RatingΒ 
2.0
πŸ”§ Car Belts, Hoses & Pulleys, 🏎️ Performance Car Parts & Accessories

View on AmazonView on Π―M

Media

(2)
img 1 attached to πŸ”‹ 5-Foot Fuel Line: 1/4" ID NBR Hose 4 AN Push on Hose Engine Liner for Fuel Systems, E85, E10, Coolants, Oil, Air, Methanol, Lubricant
img 2 attached to πŸ”‹ 5-Foot Fuel Line: 1/4" ID NBR Hose 4 AN Push on Hose Engine Liner for Fuel Systems, E85, E10, Coolants, Oil, Air, Methanol, Lubricant

Details

BrandSteber
MaterialNbr
ColorNBR hose

Description of πŸ”‹ 5-Foot Fuel Line: 1/4" ID NBR Hose 4 AN Push on Hose Engine Liner for Fuel Systems, E85, E10, Coolants, Oil, Air, Methanol, Lubricant

ID: 1/4 inch, OD: 0.47 inch / 12mm, 4AN NBR liner Fuel Injection hose, 5 feet. Use hose barbs and clamps, transfer of petroleum products fuel lines for small engines. Handles temperature ranges of -40 to +275 degrees F. Designed for conveying gasoline, E-85, diesel, and bio-diesel fuels in cars, trucks, buses, etc. Working Pressure 2Mpa. Burst Pressure 6Mpa. The Fuel Lines for fuel injected systems, are oil resistant,cold-resistant and ethanol tolerance.

Reviews

Global ratings 4
  • 5
    1
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    3

Type of review

Revainrating 1 out of 5

This is NOT a fuel line. There is no marking to indicate that it is designed for fuel.

This is NOT a fuel line. There is no marking to indicate that it is rated for fuel or should be used in applications where fuel is used. It is also very stiff and hard and not suitable for fuel lines in most cases. It's just cheap nylon cord.

Pros
  • Easy to use
Cons
  • Cable is shorter than other picks

Revainrating 5 out of 5

Good quality hose. for spare parts

There is not much to say about the gas hose, but the hose is of good quality. I called Napa and they charged $64 for 3 feet. So this hose costs less than half the cost of 5 feet. Leave it in the sun for about 15-20 minutes to soften it and lubricate the end where you put it on. This helps a lot as the hose is durable.

Pros
  • operating pressure 2 MPa. Burst pressure 6 MPa
Cons
  • Negative impression

Revainrating 1 out of 5

Pinching when engine warms up

I bought this assuming it could handle vacuum pressure but I was wrong. Attempting to use this hose to connect the PCV to the oil separator resulted in the line becoming pinched after the engine had warmed up the rubber, softening it considerably. I was late with the return and had already cut the hose to the required length. This product did not work for my needs.

Pros
  • ID: 1/4" OD: 0.47" / 12mm, 4AN NBR liner Fuel Injection Hose, 5ft
Cons
  • Interval

Revainrating 1 out of 5

Not 5/32 but 3/16

This has been sold and packaged in a bag with a label showing it 5/ 32 inch fuel. line and it's a NO! This is a 3/16 inch fuel line with no markings on the hose. I bought this because I needed a 5/32" fuel line to replace the old fuel line on my 70hp Johnson/OMC outboard motor. I had no choice but to use a piece of the old fuel line and connect it to the new 3/. 16" tees. Luckily the carburetor fittings fit on this 3/16" hose. I could buy a regular 3/16" fuel line at a local parts store and it…

Pros
  • Use of burrs and clamps for hoses, fuel lines to transfer oil products for small engines
Cons
  • So far so good