NANPU 1" NPT Compressed Air Filter Regulator Piggyback Combo, 5 Micron Brass Element, Poly Bowl, Semi-Auto Drain With Metal Bracket & 0-150 Psi Gauge Review

With compressor in the basement, I added this regulator to provide regulated air to the garage. Made a nice transition to Maxline.

Great for price, but the bleeder design is bad. Good think I also have manual cable type drain on my compressor tank. The filter element may become clogged easily in dusty environments.

Regulator worked great, was packaged very well, arrived in perfect condition. Was able to move the gauge to the opposite side to be able to mount it inline with my piping configuration. Great value.

we needed to reduce the psi coming out of our air compressor down to 5-15 psi for aeration of wort in a microbrewery. We needed to purchase a sanitary filter separately, but setup & connection was fairly straightforward.

Works as expected. No leaks so far after about a month. I was able to flip the gauge over to the other side since I needed the flow to go the opposite way. Used thread sealant from autozone on the plug and it worked out great.

Worked right out the box. Had to use pipe tape to seal it on the fittings as normal. No leaks for a few months and now I leave my compressor on all that time and it never kicks on unless I use air for a bit.

I like the regulator but the gauge was a little hard to read. The marks on the gage we’re in increments of 2.5 psi and the numbers were in increments of 25, 50, 75 etc. Would’ve been nice if they were in increments of 10.

For the money this regulator has worked well for me. Not the most solid on the market but for my application it has held up.

This was a perfect solution to fixing my old ridgid mobil air 2 gal compressor. The original regulator manifold developed a crack and is no longer available by manufacturer or remake. This was cheaper and faster than going to store and piecing together a makeshift manifold out of 1/2 pipe. The fittings that come with this are not great and I did not use. I used thicker metal fittings. Can’t beat the price, perfect for a small compressor that was otherwise useless without a regulator. Would buy…

This product is well-made large easy to adjust easy to put together comes with nice fittings protecting all of the openings. Very impressed for the price. Also the two three-quarter inch couplers are beautiful and allowed me Excellent installation

Purchased this for my shop. It gets all day use every day. I use very high volume of air. I waited 3 weeks to write a review to see if I had any problems. I’ve had no leaks at all. I have a commercial air dryer pre regulator so I have seen no water in the separator at all, but it does drain easily if needed.

Good price, fast delivery.It has only been installed for a couple of days so I do not know how the longevity will be. May be challenging to make adjustments to pressure and flow.

Not good purchase if it only last a couple months instead of many decades like my other regulators I have owned.Too late to amazon return… will need to buy new, will not use this brand again obviouslyMaybe tomorrow the scared dog will stop hiding after this blew out… luckily the girlfriend wasn’t home. And I was in the house, and thankfully THE COMPRESSOR WAS SHUT OFF! Or it would have run continuously!

The regulator works fine, however, don't use the teflon tape supplied with the kit. It could certainly be a coincidence that all the pipe joints where I used the supplied teflon tape leaked, where I used the tape that I had on hand were fine, but I don't think so.

Works great for what I needed it for. It is mounted in ceiling for over head air line. It can not be bumped or I could see it cracking. Works as listed and gauge reads correct to pressure in line.

This seems to work for drying but I've been disappointed to find that the pressure regulator and gauge doesn't seem to work. I have a pressure regulator on the input side of the line before this device and the pressure registered on that gauge is nowhere near what is displayed on the dryer. The gauge on the dryer shows 6-8psi even out of the box, unconnected. I'd have sent this back but for the money, it's getting me by while I'm waiting on another manufacturer to send me a different one.