Header banner
Revain logoHome Page
๐Ÿ”ง orxplus tools deburring external tool (3mm-19mm) for efficient metal smoothing logo

๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing Review

3

ยท

Very good

Revainrating 4.5 out of 5ย ย 
Ratingย 
4.7
๐Ÿชš Industrial Drill Bits, ๐Ÿ”ช Cutting Tools

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing
img 2 attached to ๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing
img 3 attached to ๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing
img 4 attached to ๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing

Description of ๐Ÿ”ง ORXPLUS TOOLS Deburring External Tool (3mm-19mm) for Efficient Metal Smoothing

Easy to work- Attaching the deburring external chamfer tool to the end of your power drill, Use the lowest speed on the drill bit, and then slightly applying pressure to remove the burr. Cost-Effective- These deburring external chamfer tool can be used for repairing damaged bolt and tightening the nuts in place. You do not need to spend time and money to find hard-to-find or expensive replacement bolts. Safety Design- Quickly repairs damaged bolts and tightens the nuts in place without hurting your hand, no sparks, and no burns; Simplifies the repair process. Using proper speeds and feeds-Drill use 0-400 RPMs. Fit 1/8' (3mm) to 3/4' (19mm). Widely Application-Effectively used in Stainless Steel, Hardened Steel, Mild Steel, Copper, Brass, Aluminum, Fiberglass, Wood, Plastic.

Reviews

Global ratings 3
  • 5
    2
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Cuts very fast and lasts

My first ORX reamer has been used many times on stainless steel over the past year and has now only performed well in one area. So it's still good for any other diameter. And it might not wear out if I use more coolant. Unlike thin conical reamers, ORX has no side holes to eject fragments in all directions. Debris comes out the back and mostly bounces off the cartridge (but always wear gloves anyway). worth your money.

Pros
  • Drill Bits
Cons
  • New Competitors

Revainrating 5 out of 5

Well it worked! the best countersinks

While working on my machine I had to loosen the control lever on the ball joint. This is an older VW where the ball joint and control arm were still in one piece. At some point the ball joint pin broke off at the top. I've tried so many different tools. this. Thread file, thread fastening nut. for free. My new plan was to cut off the screw's bad threads and then buy a cheaper deburring tool sold under various names on Amazon. I ended up returning the cheaper tool as it did little to shear theโ€ฆ

Pros
  • electric drill parts and accessories
Cons
  • disappearing

Revainrating 4 out of 5

It works well if you know the secret ๐Ÿ˜‰

Works well if you know the secret. When I first received this nozzle, I was very upset. It pounded like a jackhammer, leaving horrible wavy, jagged surfaces on the parts. It took a bit of trial and error to finally figure out that I would get very reliable smooth cuts by setting my drill on slow and using basically my entire body weight in the drill. At that moment I was very impressed, the surface quality is almost mirror-smooth, as is usually the case. The only problem I found is the smallโ€ฆ

Pros
  • Power Tool Parts & Accessories
Cons
  • Slightly dented