Header banner
Revain logoHome Page
๐Ÿ”ง enhance your additive manufacturing with polymaker polymide samples: reinforced filament for exceptional results logo

๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results Review

3

ยท

Poor

Revainrating 2.5 out of 5ย ย 
Ratingย 
2.3
๐Ÿ–จ๏ธ 3D Printing Supplies, ๐Ÿญ Additive Manufacturing Products

View on AmazonView on ะฏM

Media

(4)
img 1 attached to ๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results
img 2 attached to ๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results
img 3 attached to ๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results
img 4 attached to ๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results

Description of ๐Ÿ”ง Enhance Your Additive Manufacturing with Polymaker PolyMide Samples: Reinforced Filament for Exceptional Results

100g glass fiber reinforced PA6 filament + 100g carbon fiber reinforced PA6 filament. It is important to have an abrasion resistant nozzle, cause glass fiber reinforced (Nylon 6) filament contains 25% chopped glass fibers by weight. 1.75mm Nylon 6 Filament.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    2

Type of review

Revainrating 1 out of 5

Wet, tangled and poor layer adhesion nothing could be worse

I dried this filament for 48 hours and still had water bubbles when printing. Even at the maximum recommended temperature of 300 ยฐC, the adhesion of the layers is poor. The sample comes without a coil, which is usually fine. This thread was tied into a knot every 10 minutes. When untangling, the thread tore in several places, which worsened the impression. I would not recommend this to any company that needs to get filament ready to print. The company didn't reply to 2 messages so good luck ifโ€ฆ

Pros
  • great product
Cons
  • obsolete model

Revainrating 5 out of 5

prints well, low distortion, sticks with glue stick

Sampled by PA6-GF and CF at Rapid 2019. Mom's garage door opener broke, nylon part was discontinued. Great opportunity to test the PA6 GF trick. Some design work in Fusion 360 and we had STL. Set Slic3r to the recommended settings on the package, launch Prusa and you're good to go. The instructions emphasize keeping the filament dry, which is why it ended up in one of my old Stratasys cartridges. I broke a piece of thread while loading the wallet, which worried me a bit, but after that I had no

Pros
  • Pleasant
Cons
  • disappears

Revainrating 1 out of 5

Hmm, no. 3D Printing Filament

This is a review I am writing in shock. First of all the delivery was fast, Revain and the seller were on it. I'm a big fan of Polymaker, from Polylite PLA and PCMax to Polymide CoPA. So far I have only ever been satisfied with Polymaker. After going through 4 spools of MatterHacker's NylonX without a single usable part, their support team gave up and said their product just couldn't make the airplane parts I make. I was looking for something durable, heat resistant, and not as horrible asโ€ฆ

Pros
  • Easy-to-Read Control Panel
Cons
  • New Competitors Have Appeared