Power Up Your Vehicle With InstallGear'S Power Distribution Block - 0/2/4 AWG Gauge & 1/0 Gauge In To (2) 4/8 Gauge Out, Perfect For Auto, RV, Motorcycle And Boat Review

This power distribution block arrived on time time and works exactly as expected. This was used to hook up a couple large inverters in my Suburban for the kids to use on long trips. I painted the block up a little to match the blue power wire, and black was used on a similar style block I had on hand to match my ground wire. Unlike many of the power distribution blocks I have used in the past, the plastic cover on this block fits pretty well!

There were two missing Allen screws, will not be able to connect the wires to the lug. Either take the refund and get stuck with the postage, or get a new one and still get stuck with the postage. Or drive 35 miles a buy Allen screws to connect the wires. So many options, for a purchase that should have been complete to begin with. I can't wait to order something else from China.

I needed a couple of these to rewire my existing amp to allow for a powered subwoofer in my Jeep Wrangler. These have a sturdy build and the wires were able to be attached securely.

For the price its a very nice distribution block.didnt come with any mounting screws though and the bottom 2 outs are a pain to use but I doubt many people will have all 4 outputs connected

Good feel to it. Doesn't feel cheap. Seems like it'll do the job just fine. 4 gauge is a tight but perfect fit don't expect to get anything bigger in the 4xout side. I only put 4ga in so can't speak for the input side but it looks like 1/0 will fit just fine.

It does exactly what it's supposed to do and doesn't look all that bad. I needed one that could handle the larger guage wires and they fit perfectly. The block is cheaper made, plain looking and no rounded off corners, but does what it's made to do with no problems.

The only, very minor, complaint I have with this product is the fitment of the plastic cover. Remember this is a power block. Power in on one side - power out on the other side. So I wish the fitment was a little better of the plastic cover and insulator. It fits pretty good , but could be just a little bit better. I wish I could give this a 4.8 out of 5 but that doesn't exist.

Were great quality, sent back bc wasn't what I needed but they felt heavy and appeared to be great solid quality. The block may not be compatible with certain batteries.

What isn’t to like? It’s simple, robust, and a great value. It doesn’t have fancy voltage readouts or groovy lights, but it doesn’t pretend to be that. It’s rock solid and easy to hide behind or under wherever you want it and allows versatile choices of input and output wire gauge.

Used for a car stereo installation. Easy to install and secure fittings. Beefy hex screw for the heavy duty input and staggered hex screws for four distribution connectors. The plastic cover snaps on but the lack of a screw down connector for the cover is less than ideal. If the cover had a more secure fitting than simple plastic snaps it would get 5 stars. As is, I have taken some safety measures to ensure my car doesn't go up in smoke.

Performs well looks great! Delivery was on time and installation was a snap thanks so much will order again in the future.

This item is great. I rewired the center console of my boat and this product can in really handy when everything is fiberglass and wood. I had to wire up multiple switches and multiple electronic parts to my boat. I would recommend these for any vehicle! I'll be buying more for future projects.

I liked the item. I bought it for distribution of 12v+ and one for 12v- in my trunk area. I will feed 12v power to relays and other things that require 12 volts. Nice product.

I am connecting one input and 3 outputs of 12 gauged copper stranded wire. At first the hold inside where the screw makes contact was not tight enough. I finally had to cut more insulation off the end of the wire and double it over for a larger diameter. Then, it fit tight and made a strong hold. The stranding was split in half during the tightening and would pull out easy. I believe solid coper wiring would be a perfect fit for those small set screws.

This item was easy to use just don't forget to have Allen Keys ready to make a tight fit to complete the job right. The block's wiring may be too short for some vehicles.

I haven't installed it and may not need it after all. But for the price I will keep it around. Does seem well made though. The block may not distribute power consistently over long periods!

great product just what I was looking for only drawback it didn't come with any allen keys to loosen the grub screws but other than that a great product

This is a great distribution block for the money compared to kicker. It does feel a little bit cheaper quality but for the money it’s great.

Nice solid piece. Only took one star off because the plastic cover doesn’t clip tight on one of the blocks. Thanks for attention.

I'M CONNECTING 2 AMPLIFIERS IN MY VW JETTA AND I WAS THINKING OF THIS DIST BLOCK WHERE TO GET ONE AND BOOM? IT POPPED UP ON AMAZON WHILE I WAS ORDERING MY SPEAKERS! THANK YOU VERY MUCH INSTALLGEAR