Header banner
Revain logoHome Page
πŸ“ zokmok template: easy tear out & perfectly suitable for all uses logo

πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses Review

4

Β·

Average

Revainrating 3.5 out of 5Β Β 
RatingΒ 
3.3
πŸͺš Router Bits, πŸ”ͺ Cutting Tools

View on AmazonView on Π―M

Media

(4)
img 1 attached to πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses
img 2 attached to πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses
img 3 attached to πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses
img 4 attached to πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses

Description of πŸ“ ZokMok Template: Easy Tear Out & Perfectly Suitable for all Uses

βœ… Flush Trim Router Bits Set Cutting Dia.- 11.9mm, 20mm,25mm,38mm. βœ… Smoother Cut - The flush trimming bit has 2 regular blades that can be especially handy in a router table so that the template runs on the bearing allowing you to cut with the grain smoothly and prevent tear-out. βœ… High Quality - C3 micro-grain tungsten carbide blades, high-quality alloy steel bodies. Heat resistant Teflon coating. When using the Router Bit, avoid collision between the alloy blade and the hard surface (cement floor or metal surface)!. βœ… Use Range - The 1/4 Router Flush Trim Bits Set suitable for Woods, MDF, laminate, particleboard, plywood compact panel, acrylic and etc. Avoid cutting metal and non-wood materials. βœ… How to Use - Choose a template timber, use the double side tape the piece and the template together, trace the template shape out on the project with a pencil, and then use the bottom bearing flush trimming bit to clean up the extra material, finally use a putty knife to remove the template.

Reviews

Global ratings 4
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    1
  • 1
    1

Type of review

Revainrating 5 out of 5

Great Quality at a Great Price

I needed a flush cutter with a top mount bearing to cut a 3/4 inch figured maple profile. I found the long straight cutting edges very aggressive and had to hang very close to my router and scramble up the cut of the material. After several rounds of the workpiece, I was able to get a clean surface with no burn marks. This cutter appealed to me not only because of its design, but also because it is said to be made of grade C3 carbide. Durability? I won't be able to assess the service life of…

Pros
  • Power Tool Parts & Accessories
Cons
  • No Instructions

Revainrating 1 out of 5

Low quality. at Power Tool Parts & Accessories

The set screw holding the bearing to the shaft broke off two bits during use and there were plenty of them. Now I have useless bits. I have tried contacting support and Revain and as there is no response they are unable to help. I bought it in May but didn't use it until August and that's when I noticed the problem. Don't buy and check and tighten the hex screws every time you use the bit. The price is good but the design and quality are not worth it. Now a few bits are useless if I can't find…

Pros
  • Excellent overall
Cons
  • Doubtful

Revainrating 5 out of 5

Good quality at a good price

Amazing quality for the price. I only used the longest. I was busy and burned out a H*****F******** router I had for a few years. I realized it was old and that was the turning point. I bought a Ry*** router and burned it in about 10 minutes. Picked this up and got a Rid*** router and it did what I was trying to do with ease. At first I thought they weren't up to the task, but those were just the routers I was using. Make sure you have a good enough router or have the ability to get a…

Pros
  • Easy to read control panel
Cons
  • New competitors have appeared

Revainrating 2 out of 5

Questionable quality control - stock still allowed for inadvertent cutting into workpiece

I bought this set to use for a variety of woodworking jobs, primarily edge trimming and other edge finishing of plywood. I was disappointed with my first use to find that the router blade cut into the surface of the plywood rather than just trimming the excess edge off the plywood. My guess is that storage and sheet stability is not as good as it should be, leading to such disappointing results. I have not tried other blade sizes; This was done with the smallest diameter bit in the set.

Pros
  • Easy assembly
Cons
  • There are other interesting options.