Header banner
Revain logoHome Page
clip-on noise filter, vskey [10pcs 9.0mm] high-frequency ferrite core choke cable clip for subwoofer, speaker, mixer, home audio device - effective noise suppressor (0.35 inch inner diameter) logo

Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter) Review

9

·

Average

Revainrating 3.5 out of 5  
Rating 
3.4
🚙 Vehicle Electronics Accessories, 🚗 Car & Vehicle Electronics

View on AmazonView on ЯM

Media

(4)
img 1 attached to Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter)
img 2 attached to Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter)
img 3 attached to Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter)
img 4 attached to Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter)

Description of Clip-on Noise Filter, VSKEY [10pcs 9.0mm] High-Frequency Ferrite Core Choke Cable Clip for Subwoofer, Speaker, Mixer, Home Audio Device - Effective Noise Suppressor (0.35 inch Inner Diameter)

*This RFI EMI Noise Filter 0.35 inch (9mm) inner diameter: Suitable for Diameter 0.27inch - 0.35inch (7-9mm) cables,Application Occasion: Clip them on HDMI/VGA/DVI cable, Power audio/Loudspeaker/Radio/Cords, Subwoofer/Amplifiers/Mixer Console line,home theater Device cords, Industrial Equipment Cords etc. *These ferrite core noise Filter,superb at reducing EMI / RFI high frequency interference caused by home appliances and electronics.Effectively screen electromagnetic interference and filter out high-frequency noise pulses.the more effectively improve the signal quality of audio and video. *Easy to install with double snap clips,can be dismountable,Just snap clip it on to a cable easily,Stop EMI and RFI effectively.and get clearer signal and audio sound quality. *The ferrite cores come in two split halves, and clamp on to the cable whether it has a connector, or is hard wired to equipment. Install the ferrite core at the equipment side of the cable. If a cable has equipment that needs to be protected on both sides, install one at each end.(Depending upon circumstances, identifying and troubleshooting both of affected and offending devices are necessary for successful installation.). [WORRY-FREE WARRANTY& Buy with Confidence ] VSKEY noise filter offer 90 days hassle-free return money back and friendly customer service.If you're not completely satisfied, simply let us know and we will offer a prompt refund or replacement, no questions asked.

Reviews

Global ratings 9
  • 5
    5
  • 4
    0
  • 3
    0
  • 2
    2
  • 1
    2

Type of review

Revainrating 5 out of 5

Quick and easy solution to RF turn on problem

I was setting up a ham radio and the remote power was shut down due to an RF signal on the AC or 12V DC side. Tied to each fishing line and checked. No more trouble. I have the largest size to fit over thick cables. Good inexpensive solution and simple solution.

Cons
  • Functionality

Revainrating 5 out of 5

Works perfectly! for automotive electronics accessories

Holy Cow! I ordered this to (hopefully) fix some very intrusive interference on my TV after installing a device next to the TV to connect to the internet from around the house. After installing those cables going to the TV, as well as the cables going from the internet device, the picture changed from barely visible to perfect. I am very happy. I wish I had tried this a long time ago.

Cons
  • Available in white only

Revainrating 5 out of 5

2009 Ford F-250 Super Crew LED Headlights and TPMS Error

Switched my 2009 F-250 to LED headlights and immediately got the message 'TPMS sensor error'. After some research I decided to give them a try as there are widespread reports of HID/LED conversions leading to RFI/EMI in car systems. Several of these chokes attached to the H13 wiring harness going to each headlamp did. No more error messages.

Cons
  • ---

Revainrating 1 out of 5

Does not work: Car electronics accessories

I have already used double-shielded thick cinch cables for my car radio. I didn't hear the typical buzzing feedback, more like a fast clicking feedback noise. This product did not help. I believe this product is for poorly shielded cables. However, if you already have properly shielded cables, your feedback noise is due to a different problem. However, I tried another product from Revain that really helped me. https://www.amazon.com/dp/B000BCDQ44/ref=cm_sw_r_cp_apa_i_leZNFb2DDNN88?_encoding=UTF8…

Cons
  • Null

Revainrating 2 out of 5

Wish you had "real " performance with one of these snap ferrites

All snap ferrites (except one) (have minimal technical details. At MINIMUM they should specify (1) the maximum current saturation (where the EMI filtering goes away) and (2) either the effective frequency range or the material (from which you can look at the frequency range) Yes, they're cheap compared to other sources, but it's hell if they'll do all that well is to filter out conducted EMI. As you can imagine, for my application (filtering 180-200MHz in the cable that runs the cable from the…

Cons
  • Slightly wrinkled

Revainrating 5 out of 5

Remove radio interference from LED headlights.

I have a 1997 Mazda Protege DX with radio. I'm restoring it because it was my mother in law's car and she died about a year ago and I'm going to restore it and in the process giving to one of the kids I installed some hidden LED headlights with ballast after I did that I could almost only record a few radios when the lights were on due to all the noise. I was doing some research on ferrite and saw this product I just bought and when I installed it in series between the LED ballast in the…

Cons
  • old

Revainrating 1 out of 5

Doesn't work

I've used double shielded thick RCA cables for my car radio before. I didn't hear the typical humming feedback, but more of a fast clicking feedback noise. This product did not help. I believe this product is for poorly shielded cables. However, if you already have properly shielded cables, your feedback sound is due to a different problem. However, I tried another product from Revain that really helped me. https://www.amazon.com/dp/B000BCDQ44/ref=cm_sw_r_cp_apa_i_leZNFb2DDNN88?_encoding=UTF8&ps…

Pros
  • Works great for me
Cons
  • No instructions

Revainrating 2 out of 5

I wish they had some "real " performance with one of these snap-on ferrites

All snap-on ferrites (with one exception) (have a minimum of technical details. You should specify at least (1) the maximum current up to saturation (where EMI filtering disappears) and (2) either the effective frequency range or the material (from which you can read the frequency range) yes they are cheap compared to other sources but that sucks if they want to do a good thing filtering out conducted EMI. As you can imagine for my application (filtering 180-200MHz in the cable that runs the…

Pros
  • Delivery was very quick
Cons
  • crumpled

Revainrating 5 out of 5

Eliminate radio interference from LED headlights.

I have a 1997 Mazda Protege DX with radio, I am restoring it because it was my mother in law's car and she died about a year ago and I will be restoring it and giving it to one of the kids while i installed some hidden ballasted led headlights, after i did that i could almost only catch a few radios due to all the interference when the light was on i installed them in series between the led ballast in the headlights, about 90 % of the static was gone and I was able to pick up my radios.

Pros
  • Absolute Legend
Cons
  • Great Price