Header banner
Revain logoHome Page
🌟 sparkly glitter 3d printer filament by eryone: enhancing additive manufacturing quality logo

🌟 Sparkly Glitter 3D Printer Filament by ERYONE: Enhancing Additive Manufacturing Quality Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(1)
img 1 attached to 🌟 Sparkly Glitter 3D Printer Filament by ERYONE: Enhancing Additive Manufacturing Quality

Description of 🌟 Sparkly Glitter 3D Printer Filament by ERYONE: Enhancing Additive Manufacturing Quality

Gypsophila sparkling PLA 3D filament material with shiny bright surface and little laminated striation. Print Temperature Range & Diameter: 190-220°C. 1.75mm (tolerance ±0.03mm). We recommend hardened steel nozzle 0.5mm. Brass, and other softer alloy nozzle, may wear out. No bubble or dust inside, lower clog or tangling rate. Sealed vacuum bag to keep it dry and keep out dust. Net weight 1kg, shipping weight 1.35kg; spool inner diameter 57mm, spool outer diameter 200mm, height 64mm.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

Absolutely gorgeous color

I bought this thread because of the amazing color and the reality did not disappoint. Although the filament on the spool may appear slightly darker than the photos, the finished product will show some sheen. The quality of the thermopile I printed was amazing - it even covered up to 240°C very well, although I printed with the same settings as for other PLAs: 215°C (first layer) and 210°C for the nozzle. , 60˚C for bed. I was a bit concerned that the glitter might have issues with the 0.2mm…

Pros
  • Vacuum sealed to keep out dust and moisture.
Cons
  • New competitors have appeared

Revainrating 3 out of 5

Quality control 3D printing filament

Use on Prusa 3D printer, heating temperature 200 degrees, bed temperature 55 degrees1. The carrier/dealer did an excellent job of delivering the product to me. And the product was 2 days later with Prime.2. While making Covid-19 face shield bandages (link to Thingiverse.com) it was taking me 2 hours to print when a PLA bump got stuck in my extruder drive. This "bump" was discovered after printing 12 rims from a new roll. I lost the print and had to unload and cut 12 inches and then reload the…

Pros
  • Temperature range and printing diameter: 190－220℃. 1.75mm (tolerance ±0.03mm). We recommend a 0.5 mm hardened steel nozzle. Brass and other softer alloy nozzles can wear out.
Cons
  • Incredible piggy bank

Revainrating 2 out of 5

Clog City (do not buy if you have a company)

I have ignored reviews of this filament as I usually find filament reviews of questionable quality but this filament is so bad that I had to take the time to write a review which I very rarely do. The layer adhesion seems to be good, I have not encountered any problems in this regard when printing. However, the problem arises because this thread is not printed. For starters, using the same general temperature settings I use for every PLA I use in my print shop (215), I found this filament to be

Pros
  • net weight 1kg, packaging weight 1.35kg; Coil inner diameter 57mm, coil outer diameter 200mm, height 64mm.
Cons
  • boring packaging