Header banner
Revain logoHome Page
eryone glitter 3d printer filament logo

ERYONE Glitter 3D Printer Filament Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to ERYONE Glitter 3D Printer Filament
img 2 attached to ERYONE Glitter 3D Printer Filament
img 3 attached to ERYONE Glitter 3D Printer Filament
img 4 attached to ERYONE Glitter 3D Printer Filament

Description of ERYONE Glitter 3D Printer Filament

Gypsophila sparkling PLA 3D filament material with shiny bright surface and little laminated striation. Print Temperature Range & Diameter: 190-220°C. 1.75mm (tolerance ±0.03mm). We recommend hardened steel nozzle 0.5mm. Brass, and other softer alloy nozzle, may wear out. No bubble or dust inside, lower clog or tangling rate. Sealed vacuum bag to keep it dry and keep out dust. Net weight 1kg, shipping weight 1.35kg; spool inner diameter 57mm, spool outer diameter 200mm, height 64mm.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

Absolutely gorgeous color

I bought this thread because of the amazing color and the reality did not disappoint. Although the filament on the spool may appear slightly darker than the photos, the finished product will show some sheen. The quality of the thermopile I printed was amazing - it even covered up to 240°C very well, although I printed with the same settings as for other PLAs: 215°C (first layer) and 210°C for the nozzle. , 60˚C for bed. I was a bit concerned that the glitter might have issues with the 0.2mm…

Pros
  • Net Weight 1kg, Gross Weight 1.35kg; Coil inner diameter 57mm, coil outer diameter 200mm, height 64mm.
Cons
  • I will add later

Revainrating 3 out of 5

Quality control: 3D printing filament

Use on a Prusa 3D printer, hot end 200 degrees, bed temp 55 degrees1. The carrier/dealer did an excellent job of delivering the product to me. And the goods were in 2 days by prime.2. While making Covid-19 face shield bandages (link to Thingiverse.com) it was taking me 2 hours to print when a PLA bump got stuck in my extruder drive. This "bump" was discovered after printing 12 rims from a new roll. I lost the print and had to unload and cut 12 inches and then reload the PLA. Found another…

Pros
  • Temperature range and printing diameter: 190－220℃. 1.75mm (tolerance ±0.03mm). We recommend a 0.5 mm hardened steel nozzle. Brass and other softer alloy nozzles can wear out.
Cons
  • Expensive

Revainrating 2 out of 5

Clog City (do not buy if you own a business)

I ignored the ratings of this thread as I usually find thread reviews of questionable quality, but this thread is so bad that I had to take the time to write a review, which I very rarely do The adhesion of the layers seems to be good, I haven't noticed any problems on that front when printing. However, the problem arises because this thread is not printed. For starters, using the same general temperature settings I use for every PLA I use in my print shop (215), I found this filament to be…

Pros
  • Vacuum sealed to keep out dust and moisture.
Cons
  • Some little things