Genuine Hyundai 82651-3K000 Exterior Door Handle Assembly - Reliable and Authentic Hyundai Part Review

factory item so it fits perfectly. You don't need to remove the door panel for installation. Look for a thin plastic plug on the door. Remove and look with a flashlight, you will see a screw that needs to be unscrewed, but the trick is to leave it while the outer part comes loose.

So I bought this for my mom's car in December 2019. I put it on in January 2020. Keep in mind that this is a single car for older women and the passenger side. The door is not very used. Well the new one broke here in June 2021. Didn't even last two years. However, I will buy it again. Once again from this seller as it claims to be a genuine part. If it breaks again this rating will go down noticeably and I will buy it elsewhere. At least it's cheap.

Works. Five minutes to change. A word of caution: be extra careful not to let the screw you loosen for the other part of the handle fall into the door! I cut a piece of lightweight cardboard from a six pack holder about 1 inch wide. I folded it in half and put it in the screw hole under the real 8mm screw. falls on the cardboard "funnel" (it did) rather than the bottom of the door. I used a retractable magnetic handle (Harbor Freight) to pull the screw out and tighten it again when it was time…

Works great. YouTube videos were very helpful in the exchange procedures. It took about 10 minutes to remove the old one and install the new one, and some people might call me "mechanically DE-inclined". - from this seller the part cost about half what it would cost at the local auto parts store and three times less than the price quoted by the dealer. - The car is quite old, so I will not try to match the paint color. Just like my black side mirror (also bought from Amazon after being attacked

Exact door handle replacement for my 2007 black Sonata. Very easy to change, it took 5 minutes. Simply pry the small black plastic plug inside the door jamb, then use a magnetic wrench to loosen the single screw holding the lock barrel in place so the nut doesn't fall into the door. This is important if you want to do it the easy way. In any case, this handle can be easily inserted when the lock cylinder is removed. Then replace the lock cylinder and the plastic hole plug and you're done. Since

Paid extra to make sure I get the factory part but still screwed up. This door knob arrived (delayed) in a plain plastic bag with a vaguely labeled factory part number. It doesn't say Hyundai/Kia anywhere on the bag or part. Also the piece itself is defective as there is a rough line/burr running the full length of the handle where you grab it to open the door, my other original doorknobs don't have this, they are smooth. All these bums sell the same shit, just get the cheapest one (should be…

I drive a 2010 Hyundai Sonata 4 door. This is the third time I have ordered from a dealer and the third door handle that has come loose in the last year. The first of course was the driver's side at 1:30am when I left work 😑 The second was the driver's side about 6 months later and it wasn't even 3 months before I wanted to load groceries into my back seat and loosened the left rear handle itself. All of these handles are interchangeable regardless of the door and my car is silver and I have…

Bought for our 2010 Hyundai Sonata. It comes in black and my dad painted it gray to match the color of the car. Once installed it holds up very well and we haven't had any issues with it. If it breaks again (fingers crossed) I will definitely come back to buy it again! Note. Easy to install, YouTube videos were very helpful with the exchange procedures. Be VERY careful not to drop the screw you need to loosen/remove (the broken doorknob) into the door! When I installed it I unscrewed it a few…

Easy to install (find a video on youtube) Remove the black accessory connector then I measured and cut the PVC pipe shaft to make a sleeve and taped it in place so that Don't miss him 1 screw you need to remove to get the damn end cap off, I used a long extension, maybe 10" long, plus a socket wrench. Then CAREFULLY loosen the screw to remove the end cap that attaches to the door and holds the doorknob in place (tip: I even put a metric nut on the end screw just to be safe in case the PVC…