Header banner
Revain logoHome Page
gizmo dorks 3mm 📦 petg filament - 1kg / 2-inch logo

Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.7
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch
img 2 attached to Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch
img 3 attached to Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch
img 4 attached to Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch

Description of Gizmo Dorks 3mm 📦 PETG Filament - 1kg / 2-inch

Recommended Print Temperature: 230 - 260 C. PETG (Polyethylene Terepthalate Glycol-Modified) 3D printer filament vacuumed sealed with desiccant has high toughness with outstanding impact strength with little shrinkage compared to ABS. 2.85mm filament diameter (Dimensional Accuracy of +/- 0.03mm). Compatible with most 3D printers such as Monoprice Maker Select, Lulzbot, Flash Forge, Creality, and many more. Print Speed: 50 mm/s or less for best results.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

DON'T BUY PRESSURE CRACKS, EVEN AFTER 24 HOURS DRYING!

DO NOT BUY PRINT CRACKS EVEN AFTER 24 HOURS DRYING! EVEN ON THREE OTHER PRINTERS AND I HAVE FIVE AND ALL SHOW NO USABLE PART AND MY RAD PRINTER IS FULLY UPDATED WITH CUSTOM FIRMWARE UPGRADES LIKE BLTOUCH. MY PRINTERS WORK LIKE AN ANIMALS BUT NOT WITH THIS MATERIAL! DO NOT BUY@@@@

Pros
  • Compatible with most 3D printers such as Monoprice Maker Select, Lulzbot, Flash Forge, Creality and many more.
Cons
  • Something else

Revainrating 5 out of 5

3D Printable Silver Sphere

that I bought with a few pounds of used material. It is the most reliable and gentle printing material on the market. Having seen many of my ABS prints warp and fail, PETG is strong enough for drone parts, battery boxes, and other large structures. For small prints, PETG has a predictable (minimum) shrinkage factor. I ran this footage through an AirWolf HDR 3D printer at 240-260 with no problems.

Pros
  • Recommended print temperature: 230-260°C
Cons
  • I don't remember but there was something

Revainrating 5 out of 5

Excellent results! in 3D printing supplies

Absolutely fantastic stuff. I would give this 6 stars if I could. I had some pieces that bulged outward when lifted from the bed and tried everything to print them with clear ABS and TGlase. Shrinking with ABS - even with the case heated - continued to cause the perimeter of the part to pull in and up over the first 25 layers, straightening the curve at 45 and effectively forcing the layers into the printhead for the next layer became. It was a disaster. Best results with TGlase, but printing…

Pros
  • Print speed: 50mm/s or less for best results
Cons
  • So far so good