Header banner
Revain logoHome Page
🔧 mpa2019 magigoo nylon printing adhesive for enhanced results logo

🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results Review

3

·

Very good

Revainrating 4.5 out of 5  
Rating 
4.3
🖨️ 3D Printer Parts & Accessories, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results
img 2 attached to 🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results
img 3 attached to 🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results
img 4 attached to 🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results

Description of 🔧 MPA2019 Magigoo Nylon Printing Adhesive for Enhanced Results

WORKS ON NYLON FILAMENTS: specifically built for nylon filaments unlike many other products. WORKS ON MULTIPLE SURFACES: works on glass, PEI, Buildtak, and Kapton. EASY USE: applying Magigoo PA is as easy as child's play. Shake, press, apply to an active printing area. Magigoo welds to the 3d build plate bed seamlessly and stops prints from warping. Magigoo PA adhesive properties are designed to release the 3D print once the build plate has cooled & Magigoo PA is easily cleaned with water. LONG LASTING: Magigoo PA last for 100+ average prints; Print and print and print some more. ODOURLESS AND SAFE: Magigoo is not flammable and safe to use.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    1
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

Helps a lot with gluing nylon

This material is quite expensive for what it is, but does a great job of keeping your nylon casts on the bed. Nylon doesn't like to stick to glass in general but with the Magigoo PA I haven't had any issues with either the Taulmann 910 or the trim line, in fact the 910 stuck so well I thought I'd break my bed if I removed it. This also works for multiple prints - it's not just about the print itself. I gave up my garolite/phenolic bed in favor of glass + this is for nylon prints.

Pros
  • Industry & Science
Cons
  • Little Stuff

Revainrating 5 out of 5

Works perfectly! Be careful with ABS and Buildtek with this one.

Excellent product. I had serious issues with the nylon print until I used this one. Regardless of the bed setting/headboard/inset etc., the first nylon layer will not stick to the bed. Haven't used any other bed stick products before so can't rate this in comparison to the competition but judging by how well it has worked I have no intention of trying anything else. I found ABS adhered too well to buildtek so maybe you shouldn't use it with this combo. Isopropyl alcohol 70% cleans it directly.

Pros
  • Additive manufacturing products
Cons
  • There are other interesting options.

Revainrating 3 out of 5

Try other cheaper products before you buy this glue

I bought this product because Polymaker PA6-CF (nylon/carbon fiber) recommends it. It's easy to use. I haven't noticed a huge difference in adhesion when using the product. The thread I used shrinks a lot as it cools and comes off the bed easily with or without this glue. I've had much more success with prints using a raft and a 10mm high skirt around the piece. The apron traps heat away from the bed, limiting cooling and contraction. This product is quite expensive for its properties. I would…

Pros
  • 3D printer accessories
Cons
  • Some small things