Header banner
Revain logoHome Page
๐Ÿ–จ๏ธ enhanced micro direct extruder for creality printers logo

๐Ÿ–จ๏ธ Enhanced Micro Direct Extruder for Creality Printers Review

3

ยท

Very good

Revainrating 4 out of 5ย ย 
Ratingย 
4.0
๐Ÿ–จ๏ธ 3D Printer Parts & Accessories, ๐Ÿญ Additive Manufacturing Products

View on AmazonView on ะฏM

Media

(3)
img 1 attached to ๐Ÿ–จ๏ธ Enhanced Micro Direct Extruder for Creality Printers
img 2 attached to ๐Ÿ–จ๏ธ Enhanced Micro Direct Extruder for Creality Printers
img 3 attached to ๐Ÿ–จ๏ธ Enhanced Micro Direct Extruder for Creality Printers

Description of ๐Ÿ–จ๏ธ Enhanced Micro Direct Extruder for Creality Printers

Fits: CR-10 / CR-10-S5 / CR-10-S4 / CR-10S / CR-10 MINI / CR-20 / CR-20 Pro / Ender 2 / Ender 3 / Ender 3 Pro. Orifice size: .4mm. Filament size: 1.75mm. Made in USA by Micro Swiss.

Reviews

Global ratings 3
  • 5
    2
  • 4
    0
  • 3
    0
  • 2
    1
  • 1
    0

Type of review

Revainrating 2 out of 5

A lot of tweaking is needed to get good prints

I bought this as an "upgrade" for my Ender 3v2 hot end and extruder. First, I've never gotten a better print than what the stock hotend and extruder gave me. In fact, the quality has gone down. It got better, but I spent HOURS tweaking the settings and figuring out what this thing wants to see. I lost ALL adhesion on the first layer (after re-leveling the bed and resetting the z-offset). Changed to stock, no problems with the clutch. I'm not sure what this is about, but it was a huge fight. Iโ€ฆ

Pros
  • Filament size: 1.75mm
Cons
  • There are new competitors

Revainrating 5 out of 5

What can I say

First of all it was a complicated installation on Ender 3 v2.The good1. Beautiful machined aluminum parts2. Excellent dual feed extruder and easy to set up3. No more clicks when adjusting (Z-Offset)4 Better tip, or at least looks better with this setting5 Considering the price of a separate tip, it's a cheap install1. Lots of videos online plus good PDF online2. All inclusive3. Fits perfectly 4. I had to adjust the PDI (heater temperature), which is easy to do with the Jyers firmware in Gitโ€ฆ

Pros
  • Fits: CR-10 / CR-10-S5 / CR-10-S4 / CR-10S / CR-10 MINI / CR-20 / CR-20 Pro / Ender 2 / Ender 3 / Ender 3 Pro
Cons
  • No Automat

Revainrating 5 out of 5

That's great. Easy to install and better (in many ways) E3D Hemera

I bought both E3D Hemera and Mirvo Swiss DD full metal for my Ender 3s. Each extruder has its own advantages. But I will mostly switch to Micro Swiss. Packing, everything was packed in small plastic bags and packed in a big carton. The quality of the packaging and graphics were top notch. It can take a lot of improvement if you want your product to stand out in stores. Which I think they have in micro centers. It was easy, they have instructions online, but they use different terms for some ofโ€ฆ

Pros
  • Hole size: 0.4mm
Cons
  • No power