Enhance Efficiency with WORKSHOP Wet/Dry Vacs Vacuum Adapter WS25055A Combo Kit Review

Купите этот "набор", так как это единственный способ получить переходник для шланга с 1 7/8 на 1 1/4, он есть, поэтому я I'm happy. I think I'll figure out what to do with other adapters that I honestly don't need right now. They are all well made. So if you need adapters for your shop vacuums, buy these.

These are not adaptors: they are of a diameter to match the diameter they need to be fitted to, meaning they will not fit inside or outside the duct The administration. It's like the manufacturer had no idea how to use the adapter and just made something of the specified diameter. So it is a waste of the manufacturer's efforts, the carrier(s)' energy, and the buyer's money.

Don't buy this, SERIOUSLY! There are reviews of workarounds, listening to a rubber clutch to get it to shape what you want, but really not worth it, I've tried. Yes you can mold 1 part but it will still pop out and the other 2 parts that come with the kit are hard plastic and will not fit into anything especially the large straight coupler, it is exactly the same size as the reducing coupling, so it doesn't fit. does not work as expected as a coupler. Everything around is worthless. Don't buy…

The My Shop vacuum has a 2 1/2 inch hole so I took the hose and these attachments, they don't fit the vacuum or my other tools (Dewalt planer). I had to drill a 2.5" hole in the wood and use a table saw to reduce the diameter and then a file to fit. It works, but it takes time and effort. I needed a turnkey solution. I would call it a bushing as my other jets were exactly the same diameter or fit into this element. Before you buy, check what your app is. Not a bad product but more information…

Bought this set because I only needed one adapter and the other two didn't work. So from that point of view it is quite expensive and wasteful. I needed an adapter to go from 1 7/8" to 1 1/4". I bought a micro cleaning kit for 1 1/4" hoses. I read some of the reviews and some said it didn't fit and others said it would work with a little extra effort. I couldn't find it anywhere else so I got it Bought it. When it arrived I was ready to boil some water to heat it up and stretch it, as one…

The heat gun tip posted by another reviewer worked great and provided a precise custom fit. The narrow end of the adapter is too small to fit over the dust outlet that a dust bag would normally hold, but which can only hold as much as needed before needing to be emptied. Dewalt's custom size exhaust port makes it difficult to find a vacuum connection. Every plug I tried was either too big or too small. Heating the narrow end of the thick plastic adapter in this kit with a heat gun set on low…

Straight cylindrical (slicer) did not find application, other parts are good for my project. Some people get confused with sizes because the sizes given sometimes don't show which diameter is which, so I measured them and they look like this: The largest straight piece is 2" and 5/16" ID (ID), 2" OD and 1/2. , made in USA; the next wider part is straight, ID 2&1/4", the smaller part tapers to fit inside, OD 1&3/4", flares to the broader part, about 1&7/8", china of flexible rubber-like…

Same size as the fitting on a 1 7/8" " Hose or extension pipe. They won't fit. Here's an easy way to get the 2 1/2" to 1 7/8" adapter working. Take a pot, pour about 2 inches of water in it, and bring that Boil water. Take the adapter and place it 1 7/8" END DOWN IN BOILING WATER. Leave in boiling water for 2-3 minutes. Because the adapter is made of hard rubber, heat softens the rubber, making it easy to stretch when working on the end of a 1 7/8" hose or extension fitting. This makes it a…

So I just bought this for the 2-1/2" to 1-7/8" adapter. I didn't like buying all three, but I was hoping I could use the floor brush from my old vacuum, which was 2-1/2, on my new vacuum, which is 1-7/8. Well forget it. The larger end fits snugly to the diameter of any tool of this size, meaning it won't slip in. The smaller end also fits my 1-7/8 tube snugly, meaning it doesn't slip in either. All I did was slide the smaller end over my tools of this size. Okay, then what should I do about it?