Header banner
Revain logoHome Page
πŸ”΄ energy suspension red 4.3121r axle pivot arm with thrust washers logo

πŸ”΄ Energy Suspension Red 4.3121R Axle Pivot Arm with Thrust Washers Review

4

Β·

Very good

Revainrating 5 out of 5Β Β 
RatingΒ 
4.8
πŸ’ͺ Performance Parts: Shocks, Struts & Suspension, 🏎️ Performance Car Parts & Accessories

View on AmazonView on Π―M

Media

(1)
img 1 attached to πŸ”΄ Energy Suspension Red 4.3121R Axle Pivot Arm with Thrust Washers

Description of πŸ”΄ Energy Suspension Red 4.3121R Axle Pivot Arm with Thrust Washers

Durability is superior for cars, trucks and SUVs; road salt, oil, and a host of other common under car contaminants will eventually destroy the rubber bushings on your vehicles, not to mention the weight and torque forces that typically compress rubber. Hyper-Flex replacement polyurethane components stand up well to contaminants that often destroy rubber and have been engineered to give longer-lasting performance and not compress permanently. Hyper-Flex is offered in a variety of durometers (firmness or softness), depending on product application; performance tested and race proven; used for all of Energy Suspension products that require a higher level of performance and durability. If you are modifying, building a new vehicle for scratch or restoring an old one, Energy Suspension's Hyper-Flex performance polyurethane should be the 'ground zero' focus of your present and next vehicle plans. Over two decades of in-house experience in innovating, engineering and formulating wide selection of polyurethane components for many different industries, Energy Suspension has qualified as premier manufacturer of high quality polyurethane products. Durability is superior for cars, trucks and SUVs; road salt, oil, and a host of other common under car contaminants will eventually destroy the rubber bushings on your vehicles, not to mention the weight and torque forces that typically compress rubber. Hyper-Flex is offered in a variety of durometers (firmness or softness), depending on product application; performance tested and race proven; used for all of Energy Suspension products that require a higher level of performance and durability. If you are modifying, building a new vehicle for scratch or restoring an old one, Energy Suspension's Hyper-Flex performance polyurethane should be the 'ground zero' focus of your present and next vehicle plans. Over two decades of in-house experience in innovating, engineering and formulating wide selection of polyurethane components for many different industries, Energy Suspension has qualified as premier manufacturer of high quality polyurethane products.
Hide

Reviews

Global ratings 4
  • 5
    3
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    0

Type of review

Revainrating 5 out of 5

good bushing - performance parts and accessories

Put this in 99 F250 7.3. Factory bushings cracked on one beam, OK on the other. Significantly improved front end stiffness and handling. Would buy again

Pros
  • Control levers and parts
Cons
  • Lots of stuff

Revainrating 5 out of 5

94.5 F350PSD. - Performance Parts & Accessories

Just what I need for my 94.5 f350 Dual. Note that when replacing with this kit, the metal bushing used in the original style remains in the axle. Remove just the rubber, clean the bushing well and lubricate well with the grease provided and press in with a ball joint press or large clamp.

Pros
  • Shocks, Struts & Suspension
Cons
  • Will not fit all

Revainrating 4 out of 5

Great product for F250 2001 Lariat

They were used to replace the original bushing on a 2001 F250 Lariat. Installing them is much easier than removing the old ones. They were installed without removing the axles. These bushings help eliminate the "death wobble" I was beginning to experience and stop the feeling of wandering through the steering wheel.

Pros
  • Bushing kits
Cons
  • Not the best

Revainrating 5 out of 5

Before buying, carefully inspect the condition of the old bushings.

The suspension is reinforced, which is good. These bushings have no outer jacket. The outer shell of the old bushing should remain in the I-beam spigot (the hole that holds the bushing). These bushings are pressed into the outer shell of the old bushing. This means that any rubber residue in the old bushing must be removed from the bodywork in order to install these new bushings. The old rubber grommet is glued to the outer shell. I had to use a hammer, chisel and file, not easy, annoying. Then

Pros
  • Performance parts and accessories
Cons
  • ---