Header banner
Revain logoHome Page
enhance your 3d prints with eryone sparkly glitter shining pla filament logo

Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament
img 2 attached to Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament
img 3 attached to Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament
img 4 attached to Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament

Description of Enhance Your 3D Prints with ERYONE Sparkly Glitter Shining PLA Filament

Gypsophila sparkling PLA 3D filament material with shiny bright surface and little laminated striation. Print Temperature Range & Diameter: 190-220°C. 1.75mm (tolerance ±0.03mm). We recommend hardened steel nozzle 0.5mm. Brass, and other softer alloy nozzle, may wear out. No bubble or dust inside, lower clog or tangling rate. Sealed vacuum bag to keep it dry and keep out dust. Net weight 1kg, shipping weight 1.35kg; spool inner diameter 57mm, spool outer diameter 200mm, height 64mm.

Reviews

Global ratings 3
  • 5
    1
  • 4
    0
  • 3
    1
  • 2
    1
  • 1
    0

Type of review

Revainrating 5 out of 5

Absolutely beautiful color

I bought this thread because of the great color and the reality hasn't disappointed me. Although the filament on the spool may appear slightly darker than the photos, the finished product will show some sheen. The quality of the thermopile I printed was amazing - it even covered up to 240°C very well, although I printed with the same settings as for other PLAs: 215°C (first layer) and 210°C for the nozzle. , 60˚C for bed. I was a bit concerned that the glitter might have issues with the 0.2mm…

Pros
  • Gypsophila Sparkling PLA 3D fiber material with a glossy bright surface and small laminated stripes.
Cons
  • Slightly torn

Revainrating 3 out of 5

Quality Control: 3D Printing Filament

Use on a 3D printer Prusa Hotend 200 degrees, layer temp 55 degrees 1. The carrier/dealer did an excellent job of getting the product to me. And the goods were in 2 days by prime.2. While making Covid-19 face shield bandages (link to Thingiverse.com) it was taking me 2 hours to print when a PLA bump got stuck in my extruder drive. This "bump" was discovered after printing 12 rims from a new roll. I lost the print and had to unload and cut 12 inches and then reload the PLA. Found another "bump"…

Pros
  • Vacuum sealed to keep out dust and moisture.
Cons
  • Doubtful purchase for the elderly

Revainrating 2 out of 5

Clog City (don't buy if you have a company)

I have ignored reviews on this thread as I usually find thread reviews of questionable quality, but this thread is so bad that I had to take the time to write a review, which I very rarely do. The layer adhesion seems to be good, I have not encountered any problems in this regard when printing. However, the problem arises because this thread is not printed. For starters, using the same general temperature settings I use for every PLA I use in my print shop (215), I found this filament to be…

Pros
  • No blisters or dust inside, less clogging or tangling.
Cons
  • unreliable