Header banner
Revain logoHome Page
🔥 optimizing esun filament dehydration for printing logo

🔥 Optimizing ESUN Filament Dehydration for Printing Review

3

·

Average

Revainrating 3.5 out of 5  
Rating 
3.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔥 Optimizing ESUN Filament Dehydration for Printing
img 2 attached to 🔥 Optimizing ESUN Filament Dehydration for Printing
img 3 attached to 🔥 Optimizing ESUN Filament Dehydration for Printing
img 4 attached to 🔥 Optimizing ESUN Filament Dehydration for Printing

Description of 🔥 Optimizing ESUN Filament Dehydration for Printing

【eBox Storage Box】Designed to keep filament dry and dehumidify various kind of filaments, especially those moisture sensitive filaments. Provide a dry storage environment for filament. 【Keep Filament Dry】Designed to lay in your filaments and dehumidify to keep them dry. Made of high temperature resistant material, it can bake your filament at a designated temperature for hours. If you have problem in heating , please feel free to turn to us. 【Measure Filament Weight】Freely set the drying heating time, temperature and empty disc weight for your needs. Monitor the temperature gear inside the box and remaining material weight timely. 【Comprehensive Dust-proof】Sealed protection, comprehensive dust-proof, and no impurities. With Special tank for dryer bag and Anti-slip foot pad, which is convenient for recycling. 【Energy Saving】Equipped with LED screen, the light can be turned off automatically to save power. Great companion for any 3D FDM printers.Any problem, please feel free to contact us. Please notice that the inside box temperature is 36°C-50°C, and the hot plate temperature is 50°C-80°C, the inside box temperature cannot reach 80°C.

Reviews

Global ratings 3
  • 5
    1
  • 4
    1
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

Absolutely Terrible

Ordered one to store my filament. The first arrived with a huge crack in the pump, rendering it unusable. I ordered a replacement and it came with a broken pump! However the tear was quite small and the pump was still sucking a bit so I decided to give it a try - if it works I can glue it on with epoxy or super glue, no big deal. However, it didn't work. I tried to inflate the bag for several minutes but to no avail. Then I tried my Dyson vacuum - no luck. In desperation, I tried my shoppyk…

Pros
  • Energy Saving
Cons
  • High Price

Revainrating 4 out of 5

Best 3D printing consumables I've found

PROS: The pockets are big enough to hold all my filament. Others I tried were very dense. The pump is really good, good quality. The bags seem to be holding a vacuum so far. However, there is not much time to say for sure. I will come back and update in a week. CONS: The vacuum port has nothing to help you seal and remove air. So if you put it on a flat surface, you can't get it to pull the vacuum. If you can stick it on the edge of a spool of thread you can make it work, but it's not easy. I…

Pros
  • Full dust cover
Cons
  • Some small things

Revainrating 5 out of 5

Great addition for PLA printers

The eSun eBox is used to dry the PLA filament during printing. Keeping the PLA filament dry is critical to getting the best prints. [Also, I keep each spool of filament in a sealed Sistema container with desiccant bags to keep the filaments dry.] To use, simply pop a desiccant bag or two into the back of the machine behind the fan (first photo). ), place the spool of thread on the two spools and close the cover. The thread runs through a small hole in the writing; eSun provides a guide that…

Pros
  • Keeps the filament dry
Cons
  • I will add later