Header banner
Revain logoHome Page
🟡 high-accuracy novamaker yellow abs filament - 1kg spool, 1.75mm diameter logo

🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter Review

3

·

Poor

Revainrating 2.5 out of 5  
Rating 
2.3
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter
img 2 attached to 🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter
img 3 attached to 🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter
img 4 attached to 🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter

Description of 🟡 High-Accuracy NOVAMAKER Yellow ABS Filament - 1kg Spool, 1.75mm Diameter

✅【Risk-Free Service】One-month free trial, Lifetime Quality Promise and Money Return Service if you’re not entirely satisfied. Professional printing advice from technique support team make sure your prints SMOOTH & STABLE. ✅【High Stability and Durability ABS Filaments】Made by TAIWAN virgin ABS material with best performance, Less Odor, Less Warping & Clog-Free, Bubble-Free. Stronger than PLA and PETG, Ensure Diameter 1.75mm + / - 0.03 mm. ✅【Tangle-Free Tips】1kg Yellow ABS Filament dried 24 hours before packaging and vacuum sealed with nylon bag. To Avoid being Tangled, Filament should be fix into Spool Holes after Every Time Use. ✅【Printing Tips】Recommended Printing Temperature 230°C - 260°C, Bed 85°C - 100°C. ABS Spool Diameter: 7.8" - Spool Width: 2.6" - Spool Hub Hole Diameter: 2.1". ✅【Cost-effective & Wide Compatibility】Manufacturer NovaMaker has over 8years 3D filament R&D experiences, and produce all kinds of filaments in large scale with premium quality, which contribute to 3d filament cost-effective and reliable for 1.75mm FDM 3D printers + 3D Pen.

Reviews

Global ratings 3
  • 5
    0
  • 4
    0
  • 3
    2
  • 2
    0
  • 1
    1

Type of review

Revainrating 1 out of 5

Poor build plate adhesion, sloppy winding, multiple failed prints NEVER AGAIN

This is my FIRST AND LAST time to buy Novamaker Filament. Only rate this 1 star because 0 stars is not an option. The build plate adhesion on this material is the worst filament I've ever used - it doesn't stick to the build plate at all at normal extruder temperatures. : Forget at temperatures below 240 C. Blue Ribbon? Glue stick? Does not matter. This material will not stick to anything unless you are printing at 240-250°C. (By contrast, Hatchbox and eSun ABS filaments adhere perfectly at…

Pros
  • Industrial & Scientific
Cons
  • boring packaging

Revainrating 3 out of 5

turns out great but needed drying

So I totally fell for other reviews showing photos of their prints after acetone. I had the idea that I would like to make a bowl of yarn out of it as a gift and I can say that it ended up being perfect. However. When I first received the filament it printed pretty poorly. Came in a plastic bag but no vacuum packaging. The first print was quite bubbly and rough. I almost sent it back, but I *really* wanted it to work. I already had a dehydrator so I stuck it in for 4.5 hours at 150F. It helped…

Pros
  • 3D printing filament
Cons
  • No instructions

Revainrating 3 out of 5

Experience is required to stimulate the behavior of this thread.

My 3D printing experience so far has been with PLA and PETG and I thought I would like to invest in learning about ABS. I assure you, this is clearly not the right thread to explore these possibilities. TL; DR: This filament is wet and I've found that it doesn't stick well to the build plate or even to itself. I also found his deformity to be incredibly bad. This is my first ABS coil. Like other previous reviews, I also had to dry it at 160f for 8 hours. I finally managed to glue this filament…

Pros
  • 3D Printing Consumables
Cons
  • Damaged